Votos - 5, Puntuación media: 3.8
(
)
)
|
Resumen del manual
When using an external effects processor this will control the amount of effected signal, as it dictates the amount of signal to the Effects Send on the rear panel. Note - this will be affected by the Effect Return control (item 28) and the Master Reverb control (item 29). 3, 8, 13, 20 & 25. Mid Controls the middle frequencies on Channel 1, 2, 3, 4 and 5 respectively. 4, 9, 14, 21 & 26. Vol Controls individual volume level for Channel 1, 2, 3, 4 and 5 respectively. Overall volume will be governed by the Master Volume (item 30). 5, 10, 15, 22 & 27. Low Controls the Low frequencies on Channel 1, 2, 3, 4 and 5 respectively. 17. Switch - Speaker Emulator Switches Speaker Emulator on. The LR300 features Marshall acclaimed speaker emulation circuitry on Channel 4. When in operation, this will re-voice this channel to suit guitar. 18. LED Indicates when Speaker Emulator is on. 6 28. Effect Return This is the master mix control, allowing an external effects processor overall sound will be effected. Further control is given by the individual Effect features on each channel. 29. Master Reverb The LR300 comes complete with an spring reverb. The overall reverb level for the combo is set here, with independent controls featuring on each channel allowing you to set independent levels for each channel. 30. Master Volume The overall volume As with effects and reverb, control on each channel independent volume levels This will not however affect Out Phono on the rear panel 31. LED Indicates operating status of combo. ENGLISH LR300 Rear Panel Features (page 40) 1, 5, 7, 8 & 9. Line Input Jack This is a high impedance unbalanced input for channels 1, 2, 3, 4 & 5 respectively. Typical uses of line jack type inputs are drum machines and keyboards. 2. Mic Input XLR - Channel 1 This is a low impedance balanced input for use with microphones. 3. Effects Send Jack For connection to the input of an external effects processor. For use on Channel 1 only. 4. Effects Return Jack For connection to the output of an external effects processor. For use on Channel 1 only. 6. Mic Input XLR - Channel 2 This is a low impedance balanced input for use with microphones. 10. Line Inputs Phono These are high impedance unbalanced inputs. Typical uses of Line, phono type inputs are drum machines, C.D. players, tape deck, 4 tracks and computers. 11. Line Out Phono The Line Out can be used for connection to recording equipment for direct recording or for connection to a P.A. system. This is not affected by the Master Volume. 12. Send Jack For connection to the input of an external effects processor. 13. Return Jack For connection to the output of an external effects processor. 14. Remote Footswitch Allows you to switch internal reverb on and off from remote footswitch, (optional extra, model no. PEDL-00020) . 15. Power Switches the mains power to the combo. 16. Mains Input For connection to the mains. We would always recommend that your plug is wired in accordance with your country’s regulations. 7 CHANNEL 1 CHANNEL 2 EFFECTS REVERB MASTER LINEAR RESPONSE AMPLIFIER 0 10 0 10 VOLUME EFFECT & REVERB RIGHT MIC LEFT/ MONO R RIGHT 0 10 0 10 0 10 0 10 -10dB+10dB -10dB+10dB 0 10 LEFT/ MONO RETURN RIGHT RETURN LEFT/MONO VOLUME SEND EFFECT REVERB REMOTE LOW HIGH VOLUME L POWER 0 1 LINE INPUT EFFECT & REVERB AUDIOSTATE LR230 WARNING!: SHOCK HAZARD. DO NOT OPEN. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. THIS APPARATUS MUST BE EARTHED. AVIS!: RISQUE DE CHOC ELECTRIQUE. NE PAS OUVRIR. POUR EVITER LES RISQUES D’INCENDIE ET DE DECHARGES ELECTRIQUES, N’EXPOSEZ JAMAIS CET APPAREIL A L’HUMIDITE OU A LA PLUIE. CONNECTER CET APPAREIL A LA TERRE. CAUTION!: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. ATTENTION!: POUR EVITER LES RISQUES DE DECHARGES ELECTRIQUES, NE PAS OUVRIR LE COUVERCLE. CET APPAREIL NE COMPORTE AUCUNE PIECE SUSCEPTIBLE D’ETRE REPAREE PAR VOS SOINS. FAITES TOUJOURS APPEL A UN TECHNICIEN QUALIFIE POUR TOUTE REPARATION. HEADPHONE LEFT RIGHT LINE OUT MAINS INPUT 230V ~ 50 Hz 100 Watts OUTPUT 2x30 Watts RMS into 4 . Manufactured in England by: Marshall Amplification plc, Bletchley, Milton Keynes, England. 1 1 2 3 4 2 4 5 6 7 9 10 11 12 14 15 16 17 18 19 20 21 3 8 13 LR230 - Front Panel LR230 - Rear Panel 36 37 EFFECT VOLUME MID EFFECT VOLUME EFFECT VOLUME EFFECT -10dB +10dB -10dB +10dB -10dB +10dB -10dB +10dB CHANNEL 1 CHANNEL 2 CHANNEL 3 CHANNEL 4 MASTER LOW HIGH LOW HIGH 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 -10dB +10dB -10dB +10dB LOW MID -10dB +10dB HIGH -10dB +10dB -10dB +10dB LOW VOLUME -10dB +10dB HIGH 0 10 0 10 EFFECT RETURN MASTER REVERB 0 10 MASTER VOLUME ON AUDIOSTATE LR150 LINEAR RESPONSE AMPLIFIER LINE MIC LINE MIC CHANNEL 4 CHANNEL 3 CHANNEL 2 CHANNEL 1 REMOTE LINE OUT RETURN SEND LINE POWER LINE LINE OUTPUT 150 Watts RMS into 8 . 1 2 3 4 5 2 1 13 12 11 10 9 8 7 6 5 4 3 7 6 8 9 12 13 10 11 14 17 15 ...
Otros modelos de este manual:Instrumentos Musicales - AUDIOSTATE LR150 (798.23 kb)
Instrumentos Musicales - AUDIOSTATE LR300 (798.23 kb)