Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
For instructions on how to replace the battery, please refer to “CHANGING THE BATTERY (page 12).” 6. INPUT Jack This jack accepts input signals (coming from a guitar, some other musical instrument, or another effects unit). * The INPUT jack also serves as the power switch. Power is turned on whenever a plug is inserted into the INPUT jack, and is turned off when the plug is disconnected. When not using the unit, you should disconnect any cord connected to the INPUT jack. LEVEL Knob LEVEL Knob TONE Knob DRIVE Knob This knob adjusts the level of the effect sounds. DRIVE Knob This adjusts the amount of overdrive. Rotating it clockwise increases the effect, whereas counterclockwise rotation reduces the effect. TONE Knob This controls the tone. Rotating the knob counterclockwise will make the sound milder, while rotating it clockwise will make the sound sharper. MAKING THE CONNECTIONS AC Adaptor (PSA-Series; Optional) Electric Guitar Amplifier OUT DC 9V / 200 mA * Inserting a plug into the Input Jack will automatically switch the unit on. * Before connecting or disconnecting any patch cords, be sure all the volume controls in your system are set to minimum. This will help prevent any damage to system components. * To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections. * Always make sure to have the volume level turned down before switching on power. Even with the volume all the way down, you may still hear some sound when the power is switched on, but this is normal, and does not indicate a malfunction. * When operating on battery power only, the unit's indicator will become dim when battery power gets too low. Replace the battery as soon as possible. OPERATING THE UNIT OPERATING THE UNIT When you have made the necessary connections, set the knobs as shown in the illustration. 2 Depress the pedal switch to turn the effect on. (Make sure the CHECK indicator lights.) 3 Adjust the depth of the Overdrive effect using the DRIVE knob. 4 Adjust the tone using the TONE knob. 5 Adjust the LEVEL knob so that the level of the sound obtained when the effect is on is equal to that obtained when it is off. CHANGING THE BATTERY CHANGING THE BATTERY placed. Replace the battery following the steps below. Pedal Spring Base Battery Housing Battery Snap Cord Battery Snap 9V Battery Thumbscrew Coil Spring Guide Bush Hole 1 Loosen the thumbscrew at the front of the pedal, then lift the pedal upwards to open the unit. * The thumbscrew can be left in the pedal while changing the battery. 2 Remove the old battery from the battery housing, and remove the snap cord connected to it. 3 Connect the snap cord to the new battery, and place the battery inside the battery housing. * Be sure to carefully observe the battery's polarity (+ versus -). 4 Slip the coil spring onto the spring base on the back of the pedal, then close the pedal. * Carefully avoid getting the snap cord caught in the coil spring. 5 Finally, insert the thumbscrew into the guide bush hole and fasten it securely. SETTING EXAMPLES SETTING EXAMPLES Booster SPECIFICATIONS SPECIFICATIONS Nominal Input Level .................... -20 dBu Input Impedance .......................... 1 M. Nominal Output Level ................. -20 dBu Output Impedance ....................... 1 k. Equivalent Input Noise Level ........ -115 dBu (IHF-A Weighted, Typ.) Controls ....................................... Pedal Switch, DRIVE Knob, LEVEL Knob, TONE Knob Indicator ...................................... CHECK Indicator (Serves also as battery check indicator) Connectors .................................. INPUT Jack, OUTPUT Jack, AC Adaptor Jack (DC 9 V) Power Supply ............................... DC 9 V: Dry Battery (6F22/ 9 V) AC Adaptor (PSA Series: Optional) Current Draw ............................... 9 mA (DC 9 V) * Expected battery life under continuous use: Carbon: 30 hours These figures will vary depending on the actual conditions of use. Dimensions .................................. 73 (W) x 129 (D) x 59 (H) mm 2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches Dimensions .................................. 73 (W) x 129 (D) x 59 (H) mm 2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches ) Accessories .................................. Owner’s Manual, Dry Battery; 6F22/ 9 V(Carbon), Leaflet (“USING THE UNIT SAFELY,” “IMPORTANT NOTES,” and “Information”) Options ........................................ AC Adaptor PSA-Series * 0 dBu = 0.775 Vrms * In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice. USING THE UNIT SAFELY USING THE UNIT SAFELY Used for instructions intended to alert the user to the risk of death or severe WARNING injury should the unit be used improperly. Used for instructions intended to alert the user to the risk of injury or material damage should the unit be used improperly. CAUTION * Material damage ref...