Votos - 2, Puntuación media: 4
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
3. Connect the power cord to an AC outlet. . Nederlands Portugues Espanol Italiano Francais DeutschEnglish e Powering up and producing sound Set all volume controls to “0.” 1. Set the volume of each channel to the middle position. Also adjust the volume of the connected equipment. . Use the MASTER [VOLUME] to adjust the volume. 5. Switch on the BA-330’s power. 3. Connect your microphones, instruments, portable audio player, or other equipment. For details on connections, refer to “Example connections” (p. 9). Make sure that the volume knobs of all connected devices are set to “0.” Switch on power to the connected equipment. . 1. . * Turn on power to your various devices in the order specified. By turning on devices in the wrong order, you risk causing malfunction and/or damage to speakers and other devices. * To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections. * This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit will operate normally. * Always make sure to have the volume level turned down before switching on power. Even with the volume all the way down, you may still hear some sound when the power is switched on, but this is normal, and does not indicate a malfunction. Applying an effect Adjusting the tone quality Turn on the [EFFECT] switch for the channels to which you want to apply an effect. 1. Turn the [EFFECT] knob to adjust the type and amount of effect. . Adjusting the tone of each channel Turn the [TONE] knob of the channel that you want to adjust. Adjusting the high and low ranges of the overall sound (Equalizer) Use the [LOW] knob to boost or cut the low-frequency range. Use the [HIGH] knob to boost or cut the high-frequency range. 9 Nederlands Portugues Espanol Italiano Francais Deutsch English Example Connections Microphone Rhythm Machine Sound module Synthesizer, etc. Musical instrument (Electric acoustic guitar, etc.) Musical instrument (Electric acoustic guitar, etc.) CD player, etc. Portable audio player, etc. R L R L PCS-31 or PCS-33 Red White FS-5U FS-5L FSFoot switches Eff ect On/Off Mute On/Off Eff ect On/Off Mute On/Off STEREO LINK OUT Mixer, etc. STEREO LINK IN Set the FS-5L’s or FS-5U’s polarity switch as shown below. When making the connection using the FS-6, set the POLARITY and MODE switches as shown below. B A Other BA-330 When connection cables with resistors are used, the volume level of equipment connected to the inputs may be low. If this happens, use connection cables that do not contain resistors. * s Control panel [MIC/INSTRUMENT] switch Set this to the appropriate position according to whether a microphone or an instrument (a line- output device) is connected to CH1 and CH2. Microphone: Set to “MIC” Instrument: Set to “INSTRUMENT” CH1, CH only (monaural) CH3/CH , CH5/CH (stereo) CH3/CH4 and CH5/CH6 are stereo. Connect the following equipment Keyboards Line-level devices Guitars CD players Portable audio players, etc. • • • • • CH1, CH only [ANTI-FEEDBACK] switch Acoustic feedback will be suppressed if this is “ON.” For more about the anti- feedback function, refer to “Eliminating feedback” (p. 14). Power supply related [BATTERY CHECK/MUTE] switch When switched on, the indicator blinks, and sound will no longer be produced from the BA-330’s speakers or from LINE OUT. BATTERY indicator When you press the [CHECK/MUTE] switch, this indicator shows the amount of power remaining in the batteries. The remaining battery power indication is only an approximation. * Low charge Please insert new batteries. [OUTPUT POWER] switch If this is set to “ECO,” the volume from the BA-330’s speakers will be reduced, allowing extended use when running on batteries. With the “ECO” setting, the maximum output will be 15W. [POWER] switch This turns the BA-330’s power on/off. When this is on, the POWER indicator will light. Full charge Light Blink Light out CH1, CH (monaural) CH3/CH , CH5/CH (stereo) [TONE] knob [EFFECT] switch CH [VOLUME] knob This adjusts the tone of the instrument connected to each channel. Turning the knob toward the right makes the tone brighter. Turning this “ON” allows the reverb, delay, or wide effect to be applied to the channel. This adjusts the volume of the device connected to each channel. Turning the knob toward the right increases the volume. The level knobs of unused channels should be set to “0.” * Internal speakers overall [EFFECT] knob This knob selects the effect type and adjusts its depth for channels whose [EFFECT] switch is “ON.” Effect type REVERB This produces the pleasant reverberation that accompanies a performance in a concert hall. DELAY This produces an echo-like effect by delaying the sound. WIDE This extends the sound field to the outer edge of the speakers, producing the sensation of being surrounded by sound. EQUALIZER This lets you adjust the tone by boosting or...