Votos - , Puntuación media:
(
)
)
Fabricar: Roland
Tamaño del archivo: 311.65 kb
Nombre del archivo:
Idioma del manual:
El documento se está cargando, por favor, espere
 |
El documento se está cargando, por favor, espere
Resumen del manual
This indicator also allows you to check the battery. When the time comes to replace the battery, the indicator fails to light or becomes dimmer. PEDAL SWITCH In our unique FET switching system there are no mechanical contacts in the signal system so it won't make an audible click, and it can't make a pop. The switching totally electronically and therefore, cleanly. THUMB SCREW The battery sits in a special compartment under the same footswitch plate that activates the silent switch. When the time comes to replace the battery, you don't even need tools. * Do not remove off the screw from the unit. OPERATING THE CE-2 After connecting all cords required, set all knobs on the panel as illustrated. 2 Depress the pedal switch. Check lamp lights to indicate "EFFECT ON" and extinguishes to indicate "E FFECT OFF". *This check lamp is also used to check battery. If lamp fails to light or becomes dim, the battery should be replaced. 3 Turn RATE dial to the desired position. 4 Adjust the effect depth by turning the DEPTH dial. *Turning the RATE dial clockwise increases speed and deepen the effect. Therefore, use DEPTH dial to adjust depth to the desired level. BEFORE USING THE CE-2 • When operating the CE-2 from the AC line, use the BOSS AC Adaptor. • Avoid using the CE-2 in very dusty locations or under high temperature or humidity conditions. CONNECTING THE CE-2 TO AC ADAPTOR JACK T *, Power is «switched J i on while ! ! a plug is | \ put into i •' input jack.! AMPLIFIER Use with other effect units to expand your musical range. BOSS J-5 BOSS AC ADAPTOR MICROPHONE * Dot line for stereo connection. i Unplug this unit when it is not to be used. Be sure to tske off connecting plug from Input jack. CAUTIONS FOR REPLACING AND HANDLING BATTERY REPLACING BATTERYUSE 9-VOLT BATTERY. O Loosen the screw of pedal to open it and pull battery out. ©Replace the battery with a fresh one and put it into position. 0Set coil spring onto the projection on the rear of the pedal and shut the cover (pedal). Finally, insert the screw into the pedal guide and tighten it. At this time, be careful not to catch the battery strap in the cover or coil spring. 9 V BATTERY PEDAL (COVER) THUMBSCREW SPRING BASE COIL SPRING BATTERY CONNECTOR BATTERY STRAP PEDAL GUIDE \ BATTERY HOUSING Bescheinigung des Herstellers /Importeurs Hiermit wird bescheinigt, daß der/die/das ..........................................CHORUS CE-2 ¡Gerat, Typ Bezeichnung) in Übereinstimmung mit den Bestimmungen der Amtsbl. Vfg 1046 / 1984 I Amtsülattveriugungi funk-entstört ist. Der Oeutschen Bundespost wurde das Inverkehrbringen dieses Gerätes angezeigt und die Berechtigung zur Überprüfung der Serie auf Einhaltung der Bestimmungen eingeraumt. Roland Corporation Osaka / Japan Name des Herstellers' Importeurs CAUTIONS • When you plan not to use the CE-2 for a long period, remove the battery to -prevent current leakage and leaking of battery acid. • If battery voltage drops, effect becomes inferior or no sound is produced. To prevent this, replace the battery a little earlier. • Be sure to keep the battery snapped by the connector in the housing even when using the AC adaptor. * Even if AC Adaptor cord comes out during performance, operation immediately changes to battery, causing no trouble in continued performance. • Power is switched on when the INPUT jack is being used. When the unit is not being used, disconnect the input in order to conserve battery life. AC ADAPTOR BOSS ACA SERIES (OPTION) Use BOSS AC adaptor for AC operation. Use of different adaptors may cause improper operation or no sound. BOSS ACA 120 FOR 117V AC BOSS ACA-240 FOR 240V AC BOSS ACA-220 FOR 220V AC SPECIFICATIONS Power...............Battery 9V (1), AC Adaptor Current requirements ......9mA at 9V Control ..............Rate, Depth Others...............Normal/Effect Changeover Switch, Effect Indicator (also for confirmation of Battery Check) Jack................Input, Output, AC Adaptor S/N.................90dB or more (IHF-A) Maximum allowable input . . . . QdBm (100Hz), — 10dBm (1 kHz) Input impedance..................470kH Output load impedance.....10kilormore Dimensions............70(W) x 55(H) x 125(D)mm 2-3/4" (W)x2-1/4" (H)x5" (D) Weight..............................400g (14 oz) * Specifications are subject to change without notice. -------------------...............- ........—--For Canada- CLASS B NOTICE This digital apparatus does not exceed the Class B limits for radio noise emissions set out in the Radio Interference Regulations of the Canadian Department of Communications. CLASSE B AVIS Cet appareil numéijque ne dépasse pas les limites de la classe B au niveau des émissions de bruits radioélectriques fixés dans le Règlement des signaux parasites par le ministère canadien des Communications. o Printed in Taiwan Apr. '90 H-Products of Roland ^Roland 10401 UPC 10401 0130SS LhhJ HHHP vHIHV ViHHV VHHI^P 10981...