Votos - 1, Puntuación media: 3
(
)
)
|
Resumen del manual
To remove stubborn dirt, use a cloth impregnated with a mild, non-abrasive detergent. Afterwards, be sure to wipe the unit thoroughly with a soft, dry cloth. • Never use benzine, thinners, alcohol or solvents of any kind, to avoid the possibility of discoloration and/or deformation. need to be concerned about those around you. • When you need to transport the unit, package it in the box (including padding) that it came in, if possible. Otherwise, you will need to use equivalent packaging materials. • Some connection cables contain resistors. Do not use cables that incorporate resistors for connecting to this unit. The use of such cables can cause the sound level to be extremely low, or impossible to hear. For information on cable specifications, contact the manufacturer of the cable. • No sound is output from this unit’s speaker or any external speaker when the RECORDING OUT/PHONES jack is in use. • Due to the structural design of this instrument, small pets or other animals could end up getting trapped inside it. If such a situation is encountered, you must immediately switch off the power and disconnect the power cord from the outlet. You should then consult with the retailer from whom the instrument was purchased, or contact the nearest Roland Service Center. • Wrap the power cord around the cord hook when transporting or storing the unit. • For CUBE-120XL BASS only When connecting to an external speaker, make sure the speaker conforms to the following specifications. Impedance: 8 ohms or less Allowable power input: 120 watts or greater • For CUBE-120XL BASS only Only use speaker cable to connect the speaker. Do not use any shielded cable designed for use with guitars. • Do not insert hands, fingers, etc, into the openings in the unit. In particular, if the unit is to used in households with small children, always provide adult supervision to ensure that children keep their hands and feet out of these openings. Copyright • Recording, duplication, distribution, sale, lease, performance, or broadcast of copyrighted material (musical works, visual works, broadcasts, live performances, etc.) belonging to a third party in part or in whole without the permission of the copyright owner is forbidden by law. • Do not use this unit for purposes that could infringe on a copyright held by a third party. We assume no responsibility whatsoever with regard to any infringements of third-party copyrights arising through your use of this unit. Trademarks • The product names mentioned in this document are trademarks or registered trademarks of their respective owners. In this manual, these names are used because it is the most practical way of describing the sounds that are simulated using COSM technology. Nederlands Portugues Espanol Italiano Francais Deutsch 3 4 1. BASS INPUT Jack Connect your bass here. 2. [PAD] Switch (CUBE-120XL BASS only) This adjusts the degree of amplifi cation in the BASS INPUT circuitry (the input sensitivity). Switching this on lowers the input sensitivity (-10 dB). Switch this on if distortion occurs in this device’s input section as the result of using basses with high output signal levels or using connected devices. We recommend that this be switched off for ordinary use. 3. [COMP/DRIVE] Knob Turn this knob to COMP (Compression) or DRIVE to switch to that eff ect. Turn the knob to adjust the amount of eff ect applied. You can also turn COMP/DRIVE on and off using optional foot switches. Knob Position Description COMP This eff ect evens out the input signal levels, thus evening out the sound. Turning the knob to the right increases the compression eff ect. DRIVE This eff ect adds distortion to the sound. Turning the knob to the right increases the distortion. The COMP/DRIVE indicator lights up when COMP or DRIVE is on, and goes out when turned off . 4. [SHAPE] Switch This eff ect alters the COSM amps’ tonal characteristics. The particular eff ect obtained varies according to the amp selected with the Type switch (6). 5. [TUNER] Switch Use this when you want to tune your bass. When you turn on the switch, it will light red, and you’ll be able to use the Tuner function. For more detailed information, refer to “Using the Tuner Function” (p. 12). Panel Descriptions Control Panel CUBE-60XL BASS 11 12 15 16 17 18 19 20 21 1 3 4 5 6 7 8 9 10 22 CUBE-120XL BASS 11 13 14 15 16 17 18 19 20 22 1 2 3 4 5 6 7 8 9 10 COSM AMPLIFIER COSM AMPLIFIER 6. Type Switch that SUPER FLAT offers, this original amp also provides for the reproduction of heavy, deeply Use this to select the COSM amp type. resounding bass sounds. If the Tuner function is on, use this to select the string that you’re While faithfully reproducing the inherent sound tuning. of the bass you’ve connected, this also provides SUPER LOW for deeply resounding bass sounds. Additionally, it offers a sufficient amount of clarity, so sounds don’t get buried by the low-frequency content. [SHAPE] Switch: ON The well-defined heavy bass sounds are boosted....