Votos - 4, Puntuación media: 5
(
)
)
|
Resumen del manual
METAL STACK This is modeled on the Peavey EVH-5150. This is the high gain amp, so even at low volumes, you can still get heavy distortion and sustain. R-FIER STACK This is modeled on the MESA/Boogie Rectifier. This super high gain amp is capable of producing slash metal, grunge, and a wide range of other lead sounds. DYNA AMP This is an original amp sound that lets the player create previously unobtainable tonal changes according to the picking strength. Soft picking produces a transparent clean amp sound, while hard picking results in a deeply distorted high-gain amp sound. Once the sound is distorted, the tone then changes according to the force used in picking, greatly expanding your range of expression. Use of the RECORDING OUT/PHONES jack allows even better reproduction of the COSM-modeled sound. Panel descriptions * All product names mentioned in this document are trademarks or registered trademarks of their respective owners, and are not related to Roland Corporation. In this manual, these names are used as appropriate ways to indicate sounds that are simulated using COSM technology. 6. GAIN Knob Adjusts the LEAD channel’s distortion level. 7. VOLUME Knob Adjusts the LEAD channel volume. EQUALIZER 8. BASS Knob Adjusts the tone quality of the lower range. 9. MIDDLE Knob Adjusts the tone quality of the midrange. 10.TREBLE Knob Adjusts the tone quality of the upper range. * Because COSM faithfully models the special features and characteristics of a variety of amplifiers; no sound will be produced when BASS, MIDDLE, and TREBLE knob are all set to 0 while the Type switch is set to BLACK PANEL or TWEED. EFX (Effects) 11.EFX (Effects) Knob Turn this knob to chorus, flanger, phaser, or tremolo to select the corresponding effect. Turn the knob to adjust the amount of effect applied. The ON indicator lights up when EFX is turned on, and goes out when EFX is turned off. You can also turn EFX on and off using optional footswitches (BOSS FS-5U or FS-6). * Graduations for CHORUS, FLANGER, PHASER, TREMOLO on a panel are for reference. Be sure to check the sound as you adjust the effects. CHORUS In this effect, a slightly detuned sound is added to the original sound, giving the sound greater breadth and fullness. FLANGER This creates a flanging effect that creates a sort of spinning sensation with the sound. PHASER This effect adds a variable phaseshifted signal to the direct sound, giving the sound a swirling character. TREMOLO Tremolo is an effect that creates a cyclic change in volume. DELAY/REVERB 12. DELAY/REVERB Knob Turn this knob to DELAY or REVERB to switch to that effect.Turn the knob to adjust the amount of effect applied. * Graduations for DELAY, REVERB on a panel are for reference. Be sure to check the sound as you adjust the effects. DELAY Turn the knob to change the time and amount of delay effects. REVERB Turn the knob to adjust the reverb level. 13.POWER SQUEEZER Switch The switch lights in red when the power squeezer function is on; the switch is unlit when the power squeezer is off. Switching on the Power Squeezer function allows you to reduce the amp’s output to 2 watts. Switching this on allows you to produce a sound that preserves the same tone and balance as when the amp is played at maximum volume, but at an output of 2 watts, for volume levels that are more suitable for the average home. * The Power Squeezer function affects only sounds input through the INPUT jack. It has no effect on sounds input via the AUX IN jack. Panel descriptions Panel descriptions IN Jack You can connect a CD player, MP3 player or other kind of device and have it play along with your guitar. This accepts a stereo miniature phone plug. However, the speaker and RECORDING OUT/PHONES output is monaural. * Determine the volume level by adjusting the volume control of the connected device. 15.FOOT SW (Footswitch) Jack You can use footswitches (optional BOSS FS-5U or FS-6) connected using a connection cable (optional Roland PCS-31) to switch channels (JC CLEAN/LEAD), and to turn EFX on and off. SELECTEFX PCS-31 Polarity Switch whitered * When you connect only one footswitch by mono cable, you can only use it to switch channels (JC CLEAN/LEAD). 16.RECORDING OUT/PHONES Jack When Using RECORDING OUT Use mono 1/4” phone plugs when connecting to this jack. Volume level of RECORDING OUT can be easily adjusted if you set the CLEAN or LEAD channel VOLUME as shown in the diagram on the right. When Using Headphones Connect headphones to this jack. * No sound is played through the unit’s speaker while the RECORDING OUT/PHONES jack is in use. 17.POWER Switch This switches the power on and off. * This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit will operate normally. * If you need to turn off the power completely, first turn off the POWER switch, then unplug the power cord from the power outlet. Refer to “Power Supply” (p. 5). TUNING You can use “manual tuning...