Iniciar sesión:
Votos - 3, Puntuación media: 5 ( )

Manual de usuario Roland, modelo DN-2

Fabricar: Roland
Tamaño del archivo: 352.29 kb
Nombre del archivo:
Idioma del manual:en
Enlace gratuito para este manual disponible en la parte inferior de la página



Otros manuales para este modelo:

Resumen del manual


Copyright © 2006 BOSS CORPORATION All rights reserved. No part of this publication may be reproduced written permission of BOSS CORPORATION. Main . The DN-2 is volume control . Transforms the sound the guitar's volume is turned . By simply turning the DRIVE Whether it be a crunch sound, boosted midrange, it's right at your Panel DRIVE 12 63 4 5 Panel DRIVE 12 63 4 5 1. AC Adaptor This jack accepts adaptor (optionally By using an AC without being concerned battery power you have left. * Use only the specified AC adaptor and make sure the line voltage installation matches the input voltage specified on the AC adaptor's body. Other AC adaptors may use a different polarity, or be designed for a different voltage, so their use could result in damage, malfunction, or electric shock. * If the AC adaptor is connected while power is on, the power supply is drawn from the AC adaptor. * If there is a battery in the unit while an AC adaptor is being used, the DN-2 will switch over to battery-powered operation should the Panel Descriptions Panel Descriptions blackout or power 2. CHECK Indicator This indicator shows whether or off, and also doubles as indicator. The indicator lights is on. * If you're powering the unit with a battery and the CHECK indicator goes dim—or doesn't light at all—when you try to turn the effect on, the battery is near depletion and should be replaced. For instructions on changing the battery, refer to “Changing the Battery” (p. 11) . * The CHECK indicator shows whether the effect is being applied or not. It does not indicate whether the power to the device is on or not. 3. OUTPUT Connect this jack or another effects processor. 4. Pedal Switch This switch turns the effect 5. Thumbscrew When this screw is loosened, the pedal open, allowing you to change the battery. * For instructions on changing the battery, refer to “Changing the Battery” (p. 11) . Panel Descriptions Panel Descriptions This jack accepts or other musical effects unit. * The INPUT jack doubles as Power to the unit is turned on into the INPUT jack; the power is when the cable is unplugged. When the effects unit, be sure to disconnect the from the INPUT jack. DRIVE 87 9 7. LEVEL This adjusts the * No sound is output when completely counterclockwise. 8. TONE Knob This adjusts the tone of the sound. the TONE knob clockwise emphasizes high-frequency range, resulting in a with greater attack; turning it counterclockwise creates a soft tone with reduced treble. 9. DRIVE Knob This knob controls the amount of overdrive. Tuning the knob clockwise boosts the amount of overdrive applied. Connections * Inserting a connecting turns on the power * Raise the amp volume power to all connected * The use of an AC adaptor is unit’s power consumption is relatively you prefer to use a battery, please type. * To prevent malfunction and/or damage or other devices, always turn down the volume, turn off the power on all devices before making connections. * If there is a batteries in the unit while an AC adaptor is being used, normal operation will continue should the line voltage be interrupted due to power blackout or power cord disconnection. * Some connection cables contain resistors. When connection cables with resistors are used, the sound level to be extremely low, or impossible to hear. For A NOTE About Placement information on manufacturer of the * Once the connections power to your various devices By turning on devices in the causing malfunction and/or other devices. When powering up: Turn on the power to your guitar amp When powering down: Turn off the power to your guitar amp first. * Always make sure to have the volume level turned down before switching on power. Even with the volume all the way down, you may still hear some sound when the power is switched on, but this is normal, and does not indicate a malfunction. * When operating on battery power only, the CHECK indicator will become dim when battery power gets too low. Replace the battery as soon as possible. BOSS Compact Pedals have a non-slip rubber pad attached to its and temperature of the surface on which you place the Compact or mar the surface. You can place a piece of felt or cloth under the unit If you do so, make sure the unit will not slip or move accidently during use. Connections AC Adaptor BOSS PSA-series (sold separately) OUT 9V DC/200 mA Guitar Amp Electric Guitar DRIVE Connections AC Adaptor BOSS PSA-series (sold separately) OUT 9V DC/200 mA Guitar Amp Electric Guitar DRIVE * This unit is equipped with a protection circuit. A brief interval (a few required before the unit will operate normally. Operating DRIVE DRIVE Operating DRIVE DRIVE 1. After you have made the necessary con- 2. Depress the pedal switch to turn the nections ( p. 7, 8) , set the panel knobs as effect on. (The CHECK indicator lights shown in the illustration. when the effect is on.) 3. Adjust the amount of overdrive with the DRIVE knob. Operating DRIVE DRIVE Operating DRIVE DRIVE 4. Adjust the tone with ...


Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría