Votos - 3, Puntuación media: 5
(
)
)
|
Resumen del manual
Adjust the input level so that the Level Indicator + 8dB (red) does not light. (e. g.) Entering 80 Press the "8” key. ♦If you enter any value exceeding 100, 100 will be entered instead. ♦ If you enter a wrong value, you can erase it using the Delete Button. To recall the previous value before you enter any value with the Ten Key Pad, erase all the numbers with the Delete Button, and press the Enter Button. ♦Untill the value is entered, you cannot proceed to another parameter. Be sure to press the Enter Button. 12 Basic Procedure 3. Selecting an Equalizer Mode PROCEDURE 1 PROCEDURE 2 This selects an equalizer mode which determines how to use the E-660. While holding the Shift Button down, press the Mode Button. Select an Equalizer Mode using the ” + ’’ and" —" Buttons. PROCEDURE 3 Press the EQ Button. 13 Basic Procedure 4. Equalizing After selecting an Equalizer Mode, set the equalizer as follows: Press the EQ Button, and the Display shows the current equalizing condition. With the help of the Display, follow the equalizing procedure. Band Equalizer Mode Parameter Mode a. Channel/Band Selection In the 4 Band Mode (Serial/Parallel), you can select channel (A or B to equalize) with the Channel/Band Selector Switch. In the 8 Band Mode, you can select bands (1-4 or 5-8) to equalize. The channel and band currently selected can be seen with the indicator at the lower left of the Display (A/1-4, B/5-8). Switch 4 Band 8 Band A/1-4 Channel A Band 1-4 B/5-8 Channel B Band 5-8 Channel/Band Selector Switch A R 1-4 5-8 О ♦ When the parameter setting display (=after the EQ Button is pressed) or the graphic display is shown, the A/1-4 or B/5-8 Indicator changes according to the position of the Channel/Band Selector Switch. However, in any other display, the indication does not correspond to the switch position. To correct this, simply change the positions of the switch until they come to match. 14 Basic Procedure b. Parameter Control 1) Parameter Control with the Parameter Control Knobs Using the Parameter Control Knobs, the Q, frequency and level can be adjusted for each band. Moving a knob will change to the display of the corresponding band. ♦ Rotating the knob quickly may cause noise. Rotate It slowly. Q.........This curve controls the width of the frequency band. Freq.........This sets the center frequency where the level is changed. Level.........This sets the level of the specified frequency. In the 4 Band Mode, each knob corresponds to the band as shown below: 16 Basic Procedure In the 8 Band Mode, each knob corresponds to the band as shown below: LOW 1/5 MID LOW 2/6 MID HIGH 3/7 high л/а SI !flvf SHi 1 V 1 ! FJ(" AK — o Ü О r\ ti* Û О О О LtVfcL —îb- I RÍ O l.i Vil -=>- H-U.O LfVLl. -0- h Hi Q ‘.S'. i l —îblRLO Band 1 Sand 2 Band 3 Band 4 Band 5 Band 6 Band 7 Band S The variable ranges of the parameters which can be adjusted by Parameter Control knobs are as shown below: 8 Band 1, 2 3, 4 5, 6 7,8 4 Band Serial 4 Band Parallel LOW MID LOW MID HIGH HIGH Q 0.3 - 9.9 0.3-9.9 0.3 - 9.9 0.3 - 9.9 Frequency 30 Hz -960 Hz 200 Hz -6400 Hz 500 Hz -16000 Hz 800 Hz -20000 Hz Level -12 dB -+ 12 dB -12 dB -+ 12 dB -12 dB -+ 12 dB — 12dB— +12 dB ♦ When you have changed the display with the EQ Button or called an effect from memory (see page 27), the positions of the Parameter Control Knobs are not related to the actual values. Moving a knob even slightly cancels the current value and renew it with the position of the knob. 2) Value Entry with the Ten Key Pad The value of each parameter can also be entered with the Ten Key Pad. PROCEDURE 1 Press the EQ Button until the band display you want is called. 16 Basic Procedure PROCEDURE 2 Press the Select Button until the ► mark moves to the parameter to be set. Shift this using the Select Button \ LOW 4 S A ► Q 2.00 F r e q 5 0 H z Level 0. 0 d В PROCEDURE 3 Specify the value with the Ten Key Pad and press the Enter Button. ♦ Untill the value is entered, you cannot proceed to another parameter. Be sure to press the Enter Button. ♦ ” +" or " —" can be specified using the Button. ♦ If you enter a wrong value, you can erase it using the Delete Button. To recall the previous value before you enter any value with the Ten Key Pad. erase all the numbers with the Delete Button, and press the Enter Button. ♦ ” +" and " —" marks cannot be erased with the Delete Button. ♦ If you press the "0" or Decimal Key first for a frequency value, it will be ignored, since it does not start with a zero or decimal. ♦ If a decimal has already been entered for the Q or Level value, pressing the Decimal Key will have no effect. ☆Note on Ten Key Pad Entry ♦ If you do not press the Enter Button after specifying a value with the Ten Key Pad, you cannot go to the next procedure. ♦ If you assign any value exceeding the variable range and press the Enter Button, a value within the range will be entered, instead. ♦ To correct a wrong num...