Votos - 2, Puntuación media: 3
(
)
)
|
Resumen del manual
Operating Operating 1. After you have made the necessary con- 2. Depress the pedal switch to turn the nections ( p. 8, 9), set the knobs as shown effect on. (The CHECK indicator lights in the illustration. when the effect is on.) 3. Select the fuzz box model with the MODE knob. Operating Operating 4. Adjust the amount of distortion with FUZZ knob. The original distortion range of the selected fuzz box model is reproduced when the FUZZ knob is set anywhere from fully counterclockwise to the center position. Turning the knob past the center position enables the BOOST range, which produces distortion that exceeds that available on the original model. The BOOST range provides plenty of distortion, even when using single-coil pickups. 5. Adjust the output volume with the LEVEL knob. Normally, you should adjust the LEVEL knob so there’s no difference in the volume when switching the effect on and off. Using Using . This sticker provides the MODE knob. in the figure. * For information on modes, p. 7). Changing Changing * The use of an AC adaptor is recommended unit’s power consumption is relatively you prefer to use a battery, please use Pedal Spring Base Cord Coil Spring Guide Bush Hole Battery Snap Thumbscrew Battery Housing Battery Snap 9V Battery 1. Loosen the thumbscrew the pedal, and upwards to open * The thumbscrew can be left changing the battery. 2. Remove the old battery from housing, and remove the snap to it. 3. Connect the snap cord to the new battery, and place the battery inside the battery housing. * Be sure to carefully observe the battery’s polarity (+ versus -). 4. Slip the coil spring onto the spring base on the back of the pedal, and then close the pedal. * Carefully avoid getting the snap cord caught in the pedal, coil spring, and battery housing. 5. Finally, insert the thumbscrew into the guide bush hole and fasten it securely. Troubleshooting Troubleshooting . Is the specified adaptor separately) properly connected? Check the AC adaptor connection p. 8, 9). * Never use any AC adapter other specified for use with the FZ-5. . Is the battery low or dead? Replace it with a new battery ( p. 13). * The battery that was supplied with the unit for temporary use, intended primarily for testing the pedal’s operation. * The use of an AC adaptor is recommended as the unit’s power consumption is relatively high. Should you prefer to use a battery, please use the alkaline type. * To prevent unnecessary battery consumption, be sure to disconnect the plug from the INPUT jack when not using the effects unit ( p. 5). . Is your guitar jack? Check the connection p. 8, 9). * A cable must be connected allow the effect to be turned * If a cable is connected but no to the unit (either from a battery adaptor), the CHECK indicator will when you try to turn the effect on. No sound / low volume . Is your instrument properly connected the FZ-5? Check the connection once more ( p. 8, 9). . Is the LEVEL knob set too low? The further counterclockwise you turn the LEVEL knob, the more the volume is reduced when the effect is on. Turn the LEVEL knob clockwise to increase the volume. . Is the volume turned down on any guitar amp or effects device you have connected? Check the settings of the connected device. Setting Setting Octave Solo Setting Setting Specifications Specifications Nominal Input Level: ....................... -20 dBu Input Impedance: .............................. 1 M. Nominal Output Level: .................... -20 dBu Output Impedance: .......................... 1 k. Recommended Load Impedance: ... 10 k. or greater Controls: ............................................. Pedal switch, LEVEL knob, MODE Indicator: ............................................ CHECK indicator (for effect on/off check) Connectors: ........................................ INPUT jack, OUTPUT jack, AC Adaptor jack Power Supply: ................................... DC 9 V: Dry battery 6F22 (9 V) type (carbon)/ Dry battery 6LR61 (9 V) type (alkaline) AC adaptor (PSA-series: optional) Current Draw: ................................... 36 mA (DC 9 V) * Expected battery life under continuous use: Carbon: 3 hours, Alkaline: 10 hours These figures will vary depending on the actual conditions of use. Specifications Specifications m 2-7/8 (W) x 5-1/Weight: ............................................... 440 g /1 lb (including Accessories......................................... Owner’s manual, Mode leaflet (“USING THE UNIT NOTES,” and “Information”), dry battery 6LR61 (9 V) type ( * The battery that is supplied with the use, intended primarily for testing the unit’s We suggest replacing this battery with an Option ................................................ AC adaptor (PSA-series) * 0 dBu = 0.775 Vrms * In the interest of product improvement, the specifications to change without prior notice. For EU Countries For EU Countries For the USA FEDERAL COMMUNICATIONS RADIO FREQUENCY This equipment has been tested and FCC Rules. These limits are ...