Votos - 1, Puntuación media: 5
(
)
)
|
Resumen del manual
Vfg 1046 / 1984 funk-entstört ist. Der Deutschen Bundespost wurde das Inverkehrbringen dieses Gerätes angezeigt und die Berechtigung zur Überprüfung der Serie auf Einhaltung der Bestimmungen eingeräumt. Roland Corporation Osaka / Japan Please read the separate volume "MIDI ”, before reading this owner's manual. Copyright © 1988 by ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. Thank you for purchasing the Roland HD5 — IF. The HD5 — IF consists of an interface board for connecting a hard disk unit to the Roland S — 550, and the system disk. Using a specific hard disk unit, it is possible to store a large amount of data and to transfer data at extremely high speed. When using a brand new hard disk unit. Setup the hard disk unit as explained on page 4 "Setup". The system disk of the HD5 — IF is an updated version of the S — 550 Ver.1.0. Please study the table "Differences between the S — 550 Ver.1.0 and HD5 — IF" shown on page 16. Functions altered from the S — 550 (Ver.1.0) Descripiton Conversion A convert function that converts the S — 550's data for the S — 50 is added. Name Entry Name entry with the Mouse is easier. Map Entry The same values can be entered continuously. Split Setting Split can be set with the Tone List Display. DC - Cut A function that removes the DC contents from Wave. Data Transfer with a Floppy Disk Letters "FD” are added to a menu and command name. Loading Patch Load Tones (Tone Parameters and Wave Data) assigned to a Patch with Patch Parameters NOTES The Hard Disk Unit is extremely delicate and therefore needs careful handling. Read the owner's manual of the Hard Disk before using it. * Do not move the Hard Disk Unit while it is turned on. tin transit, pack the Hard Disk Unit in the supplied box to avoid shock or vibration. ♦While the S- 550 or the Hard Disk Unit is turned on. do not connect or disconnect the Hard Disk Unit. 1 CONTENTS 1. Hard Disks which can be used..................................................3 2. Setup .......................................................................................4 3. Normal Booting and Completion................................................13 4. Saving Sound Data onto the Hard Disk....................................15 5. Differences between the HD5 — IF and S — 550 Ver.1.0.............16 6. Backup of the HD5 — IF System Disk .......................................25 7. Data Transfer between the S — 550 and Hard Disk...................27 2 1 .HARD DISKS WHICH CAN BE USED 1. HARD DISKS WHICH CAN BE USED The hard disk units which can be used with the S — 550 are as shown below. (SCSI specifications for the APPLE Mackintosh) APPLE M - 2620 (20M Byte) M - 2644 (40M Byte) M - 2688 (80M Byte) CMS SD-20 (20M Byte) SD-80 (80M Byte) * No other hard disk unit can be used. * The APPLE hard disks are not provided with connecting cables. The APPLE connecting cable (M0206) should be purchased. 20M Byte Hard Disk Sound data equivallent to 16 floppy disks can be saved. 40M Byte Hard Disk Sound data equivallent to 32 floppy disks can be saved. 80M Byte Hard Disk Sound data equivallent to 64 floppy disks can be saved. 3 2.SETUP 2. SETUP The S — 550 and the Hard Disk can be set up in sequence as follows. 1. Install the interface board to the S - 550. 2. Connect the S - 550 to the Hard Disk. 3. Boot the S - 550 up with the HD5 - IF system disk. 4. Switch on the Hard Disk. 5. Format the Hard Disk. 6. Make the necessary settings for booting the Hard Disk. 4 2.SETUP 1. Installing the Interface Board Turn the S-550 off. then disconnect the power cord from the AC inlet. Attach the interface board using an appropriate screw — driver. * Do not loosen any screws other than shown below. * Do not touch the soldered face of the interface board * Interface board is easily damaged by statical electrified place. To preserve it on its own without connecting to the S — 550. replace it into the supplied bag. Prepare the following parts supplied with the HD5 — IF. |pi| o o -, V_ V_/ Interface Board Blind Board with Holes ScrewsCTwo for each : large and small) Procedure ©Remove the blind board on the rear panel. ©Turn over the S - 550, and remove the bottom. Front Panel Side Bottom board 5 (Ol «Ti tpi 2.SETUP 4 Locate the interface board as shown below *Do not touch the existing board of the S-550. Front Panel (§) Fix the interface board with bushes and screws. iPlace the holes onto the bushes and push the interface board. ) Attach the Internal Connector. Front Panel (?) Replace the bottom board with screws. ® Attach the new blind board. -External- Connector 6 2.SETUP 2. Connecting the S — 550 to the Hard Disk Connect the S — 550's external connector to the connector on the hard disk.(You may use either connector on the hard disk.) * Please use the cable supplied with the h...