Votos - 3, Puntuación media: 4.7
(
)
)
|
Resumen del manual
The chord will sound low, and the melody will be emphasized. Each time you press this button, the function is turned on or off. 7 (8) Hold button By pressing this button (the indicator lights up), t'he Hold function is available, so even after a key is released, the sound maintains. The sound level is determined by the sustain level set with the Sustain knob in the Envelope Generator. This hold function is not obtained if the sustain level is set to zero (decay sound). Each time you press the button, the hold function turns on or off (-► P.28). (9) Key Transpose button Transposition to any key is possible. By using the appropriate key, you can shift the pitch of the entire keyboard. Therefore, you can play a piece with many # '5 and b's in the key of C major (A minor). * How to transpose White holding the Key Transpose button down, press any key in any octave. If the indicator above lights up, transposition is completed and the JX-3P will now play in the key of the chosen note. Key Transpose 0 + DU! I Transpose □ *How to return to the normal key (C key) While holding the Key Transpose button down, press any C note, and the indicator will go out and the JX-3P has returned to the normal condition (the key of C). *This transpose function is also available for the sequencer. (You can transpose the sequencer phrase being piayed.) 8 6. Sequencer The JX-3P contains the polyphonic sequencer that-has the capacity of 128 step automatic playing. Up to 6 notes can be played at a time. Also, writing a chord is possible. ' If more than 6 notes are used in one step, the last 6 notes will be played. Sequencer □ □□ (0) Sequencer Write button Press this button to write the data into the built-in sequencer. ([5} Tie button If you wish to join notes, press this button, sequencer starts or stops. @ Rest button If you wish to write rests, press this button. (f^) Rate knob This controls the tempo of the sequencer playing. Raising this knob quicken the tempo. @ Start/Stop button This is to start or stop the sequencer playing. Each time you press this button, the Sequencer starts or stops. A) Writing You can write the pitch by playing the keybord, and the rhythm by pressing the Tie button @ and the Rest button (The pitch and rhythm should be simultaneously written.) (1)Find the shortest time value in the phrase you wish to write. Then divide the longer time values by that shortest one. [e.g.] {2)Set the Ext. Selector switch @ on the rear panel to Programmer, then the Memory Protect function will be off. BCD Memory Protect On (3)Press the Sequencer Write button (0 (the indicator lights up), then the JX-3P will be in the writing mode. * At this time, if the JX-3P is not released from the Memory Protect function, the indicators of the Tone Selector buttons 1 to 16 will light up showing that writing is impossible. Also, if the Ext. Selector switch @ is set to the MIDI position, the JX-3P is not in the writing mode. (4)By playing the keyboard and using the Tie button @ and Rest button (¡6), write steps by one after another (the indicators of the Tie and the Rest buttons light up just while these buttons are held down). 9 Also, the indicators of the Tone Selector buttons @ tell you the steps (1 to 16) and the measures (1 to 8) that you are writing. (The flashing indicator shows the measure and the lighting one the step.) [e.g.] Writing the 3rd step in the 1st measure p^pzr-jpi^ *No matter how you play the keyboard, the time values will alt turn out the same {the shortest time value). It is important to play in a non legato manner {i.e. releasing the key each time you play a key). If you play in a legato manner {i.e. pressing another key without releasing the key that you are pressing now), a chord wilt be written as shown below. legato *This applies to the Tie and the Rest buttons as well. i.e. releasing the key, then pressing the button. * 1 (eighth rest) is indicated above the Rest button on the panel, but it varies depending on the shortest time value you set. In the example, the shortest time value is / (1/16 note), so the_ value of the Rest button will be ? (sixteenth rest). (5)If writing is completed, press the Start/ Stop button @ to leave the writing mode (the indicator of the Sequencer Write button (Q) will go out and that of the Start/Stop button will light up). At this time, the phrase written will start playing. If pressing the Start/Stop button once more, the indicator will go out and the sequencer will stop ( Refer to B) Playing). *lf you wish to stop writing in the middle, press the Start/Stop button twice. start/stop twice If you press the Sequencer Write button © again after this, all the data previously written will be erased. (6) Return the Ext. Selector switch to the Memory Protect On position. nan Memory Prated On When the shortest time value is Ji (1/16 note), j (1/4 note) and J1) {1/8 note) can be replaced as follows. If J* is 1 step, j) is 2 steps and J is...