Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
With this knob at the minimum position, there will be no ambience effect. By turning the knob higher, you can produce the impression of performing in a room that has a longer reverberation time, suitable for organ performance. AMBIENCE is technology that uses RSS (p. 8). II lets you apply reverberation that is suitable for organ performance, 13.TONE CONTROL LOW knob Adjusts the volume of the low frequency range. MIDDLE knob Adjusts the volume of the mid range. HIGH knob Adjusts the volume of the high frequency range. 14.VOLUME (Master Volume) knob Adjusts the volume of the KC-1000. Depending on the volume of the input, the sound may be distorted when the VOLUME knob is at the maximum position. If distortion occurs, it can be eliminated by turning the knob approximately two gradations lower than the maximum. 15.STEREO LINK OUT, IN (Stereo Link input/ output) jacks Use these jacks when you wish to connect two KC-1000 units to form a simple PA system. For details on the Stereo Link function, take a look at Connecting Two KC-1000 Units (Stereo Link) (p. 11). 7 Panel Descriptions 5 6 7 1 L.sr Lukmo) R MC 1 ORCHESTRAL 1 [ SVNTHtAUX 1 1-«*ç--1 O © UNE PUT Section 16.LINE OUT L (MONO), R jacks If you wish to output the sound of the KC-1000 to an external PA system, connect these LINE OUT jacks to your PA system. You can also connect them to an MTR or other recording device and record the sound of the KC-1000. Make connections to either the XLR or phone jacks. If you wish to use an XLR type, use two cables to make connections in stereo. It is not possible to make connections in monaural. - You may not simultaneously use both the XLR QlOftp type and phone type LINE OUT jacks. Depending on the device that is connected, using both types simultaneously may cause malfunction. f— XLR The pin assignment for the XLR connectors is as shown below. Before making any connections, make sure that this pin assignment is compatible with that of all your other devices. 1: GND 2: HOT 3: COLD V........................-............................................. 17.LINE OUT knob Adjust the volume of the line output. Set this knob to the optimum level for the instrument connected to the LINE OUT jacks (1/4" or XLR). PHONES Section 18.PHONES jack A set of headphones can be connected here. 19.PHONES knob Adjusts the headphone volume. Before connecting headphones, you must turn the PHONES knob down to 0. ¿—-'--I The amplifier's speakers work even when headphones are connected. 20. POWER switch Switches the power to the KC-1000 on and off. When this switch is on, the indicator will light. » Before turning the power switch on/off, you NOTE must turn down the input/output knobs (all knobs other than 12 and 13) down to the minimum position. What is RSS (Roland Sound System)? This is proprietary Roland effect technology for three-dimensional localization of a sound source via a conventional stereo system. It allows the perceived location of a sound source to be placed not only in front of, or to the side of the listener, but also above, below, behind, or at a near or far distance away. What is COSM (Composite Object Sound Modeling)? Technology that virtually reconstructs an actually existing structure or material using a different means is called "modeling" technology. COSM is proprietary Roland technology that creates new sounds by combining various sound modeling technologies 8 Making the Connections and Powering Up To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections. Turn all input/output knobs of the KC-1000 (all knobs other than AMBIENCE and TONE CONTROL) to the minimum position. Keyboard Mixer j ii m ii hi ii iimjii mu niinnijQ Stereo headphones * You may not simultaneously use both the XLR type and phone type LINE OUT jacks. Once the connections have been completed, turn on power to your various devices in the order specified. By turning on devices in the wrong order, you risk causing malfunction and/or damage to speakers and other devices. 1 • Turn on the power of the connected organ and/or keyboard(s). 2* Turn on the KC-1000. 3. Turn on the power of other connected devices. 4* Adjust the volume levels for the devices. Before switching off the power, lower the volume on each of the devices in your system and then TURN OFF the devices in the reverse order to which they were switched on. This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit will operate normally. •éhf Howling could be produced depending on the location of microphone relative to speakers. This can be remedied by: • Changing the orientation of the microphone. • Relocating microphone at a greater distance from speakers. • Lowering volume levels. To connect the input jacks, use a connection cable that does not con...