Votos - 2, Puntuación media: 3
(
)
)
|
Resumen del manual
When installing the drum set, make sure the legs of the tripod are opened wide enough to keep the equipment from falling over. 4 * The figure shows the PD-125. * The only difference between the PD-125 and the PD-105 is the diameter. fig. Use a Stereo cable to make connections. If you use a monaural cable, rim shots cannot be played. You can play rim shots when the pad is connected to the trigger input shown below. Rim Shot Capable Trigger Inputs for Each Sound Module Make sure the snare drum stand you use is designed to firmly hold a 12-inch (PD- 125) or 10-inch (PD-105) drum. When mounting the PD-125/105 to a tom stand, verify the dimension of the rod. (6.3–12.5 mm) fig. Component (Parts) Names Setup Connecting to the Sound Module TD-20 2 (SNARE), 3–6 (TOM 1–4), 12–15 (AUX 1–4) TD-10 2 (SNARE) TD-8 3 (SNARE) TD-6V/6 2 (SNARE) Mounting with a Snare Stand Mounting with a Tom Stand Hoop (rim) Lugs Output jack Shell Bracket Frame Head Stand fixing screw Tuning bolts To prevent malfunction and/ or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections. Be sure to tighten the stand fixing screw to prevent the noise. Rod (diameters which can be attached: 6.3–12.5 mm) loosen tighten Adjusting the Head Adjusting the Head Tension When adjusting, use a tuning key. Heads MUST BE TUNED BEFORE PLAYING. Like with an acoustic drum, accurate and equal head tension is needed for correct triggering response. 1 Loosen the tuning bolts until a slight gap is produced. 2 Tighten all tuning bolts by fingers, as tightly as you can. Tuning bolt Washer Hoop Slight gap Using the tuning key, turn the tuning bolts two full revolutions each, thus tightening them. Tighten each tuning bolt one by one, observing the numerical order shown in the figure. 1 3 4 2 5 6 HEAD MADE BY REMO U.S.A. For Accurate Positional Sensing Correct head tension is needed for this function to perform correctly. (TD-20, TD-10, and TD-8 respond in different ways. See the respective owner’s manual.) On the PD-125/105, adjusting the head tension affects only the head response, and not the pitch of the sound, as it would on an acoustic drum. Head tension may change over a period of time, so readjust when necessary. Playing Methods Head Shots Hit only the head of the pad. With certain snare sounds, playing position will change the nuance of the sound. Rim Shots Strike the head and the rim of the pad simultaneously. Cross Stick Only strike the rim of the pad. Depending on the instrument assigned to the rim you can play rim shots and/or cross stick sounds. With certain snare and tom sounds, slight changes in the way you play rim shots changes the nuance. Normal Rim Shots (Open Rim Shots) Strike the head and rim simultaneously. Shallow Rim Shots Simultaneously strike the head near the rim and the rim itself. * See the TD-20 owner's manual for more info about which sounds allow this. * For more on settings and tones, see the respective module’s owner’s manual. Change the Nuance of the Rim Shot (Only with the TD-20) Sound Module Compatibility Chart TD-20 TD-10, TD-8 TD-6V/6 Head Shot o o o Positional Sensing o o x Rim Shot o o o Rim Shot Nuance o x x Cross Stick o o o Head Head Rim Rim Rim Head Rim Head Rim To play the cross stick, be sure that you only strike the rim of the pad. Placing your hand on the head of the pad might prevent the cross stick sound from being played properly. Specifications * In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice. PD-125 (12 inch) PD-105 (10 inch) Trigger 2 (Head, Rim) 2 (Head, Rim) Dimensions 330 (W) x 420 (D) x 112 (H) mm 13 (w) x 16-9/16 (D) x 4-7/16 (H) inches 280 (W) x 360 (D) x 112 (H) mm 11-1/16 (W) x 14-3/16 (D) x 4-7/16 (H) inches Weights 2.8 kg / 6 lbs 3 oz 2.3 kg / 5 lbs 2 oz Accessories Owner’s manual Owner’s manual Options Mesh Head (MH-12) Mesh Head (MH-10) Pad Mount (MDH-10U), Stand (MDS-20/10/8C/6/3C) Information When you need repair service, call your nearest Roland Service Center or authorized Roland distributor in your country as shown below. EGYPT Al Fanny Trading Office 9, EBN Hagar A1 Askalany Street, AFRICA AFRICAAFRICA PHILIPPINES G.A. Yupangco & Co. Inc. 339 Gil J. Puyat Avenue Makati, Metro Manila 1200, PHILIPPINES TEL: (02) 899 9801 MEXICO Casa Veerkamp, s.a. de c.v. Av. Toluca No. 323, Col. Olivar de los Padres 01780 Mexico D.F. MEXICO TEL: (55) 5668-6699 IRELAND Roland Ireland G2 Calmount Park, Calmount Avenue, Dublin 12 Republic of IRELAND TEL: (01) 4294444 IRAN MOCO, INC. No.41 Nike St., Dr.Shariyati Ave., Roberoye Cerahe Mirdamad Tehran, IRAN TEL: (021) 285-4169 ARD E1 Golf, Heliopolis, Cairo 11341, EGYPT TEL: 20-2-417-1828 REUNION Maison FO - YAM Marcel 25 Rue Jules Hermann, Chaudron - BP79 97 491 Ste Clotilde Cedex, REUNION ISLAND TEL: (0262) 218-429 SINGAPORE Swee Lee Company 150 Sims Drive, SINGAPORE 387381 TEL: 6846-3676 CRISTOFORI MUSIC PTE...