Votos - 5, Puntuación media: 4
(
)
)
|
Resumen del manual
OverDrive Distortion Compressor . Connecting OverDrive or Distortion Effects 13 Spacial effects are applied to the entire output of the PS-5. When using the PS-5 in PITCH SHIFTER / HARMONIST / DETUNE mode: Spacial effects are applied only to the direct sound (the sound that is not pitch shifted). Spacial Effector Spacial Effector . Connecting Spacial Effects Devices Description of Each Mode Description of Each Mode R The pitch of the output sound can be shifted up or down a maximum of two octaves. * This can be used both for single notes and chords. 1. After making the necessary connections (page 11), press the pedal switch to turn the effect on (the CHECK indicator should be lit). 2. Rotate the PITCH switch to select the desired degree of pitch shift. 1 2 5 7 12 (1 OCT) 24 (2 OCT) -1 -2 -5 -7 -12 (-1 OCT) -24 (-2 OCT) 3. 3. * When the stereo outs are used, the balance of the sound output corresponds to the BALANCE knob setting, with effects sound output from OUTPUT A and direct sound from OUTPUT B. 4. Connecting the optional Roland EV-5 to the EXP jack provides continuous changes in pitch, up to the amount set with the PITCH switch in Step 2. Pitch Shift (ON) (OFF) With Effect Without Effect HARMONIST Use only for single notes, not chords. This takes the input sound, creates harmonies up to two octaves above or below, and outputs the sounds together. * Monitor volume levels in this mode when the PS-5 is connected following heavy equalization or distortion effects. Harmonies may become shifted at excessive volume levels. * Using a tuner such as the optional TU-12 or TU-2 to make sure your instruments are properly tuned. Tune after setting the reference pitch A4 to 440 Hz. 1. After making the necessary connections (page 11), press the pedal switch to turn the effect on (the CHECK indicator should be lit). 2. Use the H.R KEY switch to select the same key as that of the song to be performed. For more detailed information, refer to “Key setting” (page 18). 3. 3. For more on the harmony output based on the H.R KEY switch and the PITCH switch (interval) settings, refer to “About the scale of the effect sound” (page 19). 3RD 4TH 5TH 6TH 1 OCT 2 OCT -3RD -4TH -5TH -6TH -1 OCT -2 OCT 4. Rotate the BALANCE knob to adjust the balance between the effect and direct sounds. * When the stereo outs are used, the balance of the sound output corresponds to the BALANCE knob setting, with effects sound output from OUTPUT A and direct sound from OUTPUT B. 5. Connecting the optional Roland EV-5 to the EXP jack provides continuous changes in pitch, up to the amount set with the PITCH switch in Step 3. Pitch Shift (ON) (OFF) With Effect Without Effect Key setting Key setting G G A A B B Em Em Fm F m Gm G m F E E D D C Dm C m Cm Bm Bm Am About the scale of the effect sound About the scale of the effect sound UP +5 (-4) G G A A B C C D D E E F +3 (-6) E E F F# G A A B B C C# D INPUT C C# D D# E F F# G G# A A# B -3 (+6) A A# B B C D D E E F F# G -5 (+4) F F# G G# A B B C C# D D# E DOWN +5 (-4) G F F E D D C C B A# A G# +3 (-6) E D C# C B B A A G F# F F INPUT C B A# A G# G F# F E D# D C# -3 (+6) A G G F E E D D C C B A# -5 (+4) F E E D C# C B B A A G G DETUNE This adds a subtle pitch shift to the input sound, producing a detuned effect. 1. After completing the necessary connections (page 11), press the pedal switch to turn the effect on (the CHECK indicator should be lit). 2. Rotate the PITCH switch to select the desired degree of shift. 5 Cent 10 Cent 15 Cent 20 Cent 25 Cent 30 Cent -5 Cent -10 Cent -15 Cent -20 Cent -25 Cent -30 Cent 3. 3. 93ms23ms 4. Rotate the BALANCE knob to adjust the balance between the effect and direct sounds. * When the stereo outs are used, the effects sound is output from OUTPUT A and the direct sound from OUTPUT B, with the balance of the sound determined by the BALANCE knob setting. 5. Connecting the optional Roland EV-5 to the EXP jack provides continuous changes in pitch, up to the amount set with the PITCH switch in Step 2. Pitch Shift (ON) (OFF) With Effect Without Effect T.ARM Use only for single notes, not chords. This gives you an effect simulating the change in sound with a guitar tremolo arm. The T.ARM effect is applied as long as the pedal switch is depressed. * When the pedal switch is released, the pitch returns the sound to the normal unchanged pitch. 1. Connect the PS-5 to another instrument (page 11). 2. Rotate the PITCH switch to select the desired degree of shift. Play the guitar with the pedal switch in the forward position, adjusting the effect while you lis- ten to the sound. 1 2 5 7 12 (1 OCT) 24 (2 OCT) -1 -2 -5 -7 -12 (-1 OCT) -24 (-2 OCT) 3. 3. Fast Slow Play the guitar while switching the pedal switch on and off, adjusting the effect while you listen to the sound. 4. Use the BALANCE knob to adjust the volume of the output sound. * The same sound is output from both -. +6 dB 0 dB OUTPUT A(MONO) and OUTPUT B. * Sounds input at 0 dB are output at the same volume. 5. With a Roland EV...