Votos - 4, Puntuación media: 5
(
)
)
|
Resumen del manual
Setting Receive Channel b. Receiving MIDI Information When using the RD-250s or RD-300s as a MIDI sound module, you should set the receive MIDI channel of the RD-250s or RD-300s to the same number as the transmit channel of the MIDI device that controls the RD-250s or RD-300s. ► While holding the MIDI Receive Channel Switch © down, push the key (from AO to C2} that corresponds to the MIDI channel you want • Program Change The RD-250s and RD*300s can receive the Program Change from 1 to 32 but ignore 33 to 128. * The detailed explanation on the tramsitting and receiving messages follows in the next section "3. MIDI Functions". CBM cwisr-) {Flashing I TfUftSMlT-CH IVKM <* nnniYI While holding down. Push the key that corresponds to the MIDI Channel you want. When setting the Receive MIDI channel, the indicator o the Voice Selectors will react just like when setting the Transmit MIDI channel. {See page 11 "a. Setting Transmit MIDI Channel".) 15 3. MIDI Functions The RD-250s and RD-300s can select any of the following three modes that decide how the messages are received and transmitted. (I) By taking the procedure shown from page 11 to 15, Note On/Off, Program Change and Control Change are transmitted and received. (H) Note On/Off, Program Change and Control Change are transmitted and received. • The moment a new voice is selected on the RD-250s or RD-300S, the corresponding program change number is transmitted. The chorus or tremolo On/Off is transmitted as a control change message. This setting may be used when recording the data into a MIDI sequencer and play it back. (Ill) Note On/Off, Program Change and Control Change are transmitted. Program Change, Chorus On/Off and Tremolo On/Off cannot be received. * Refer to MIDI Implementation Chart in the back of this owner's manual. How to select the above communication mode Mode (I): Turning the RD-250s or RD-300s on will automatically selects this mode. Mode (II): Turn the RD-250s or RD-300s on while holding the MIDI OUT Switch Q down. Mode (III): Turn the RD-25Qs or RD-300s on while holding down the Voice Selector Piano-1. 16 ■ Other Function • Remote Pedal Connect the supplied pedal switch DP-2 to the Remote Pedal Jack ©, and the DP-2 can be used as a remote switch for the Key Transpose, Split, MIDI OUT, MIDI Lower, MID! Upper, Receive Channel/Internal Voice, Chorus or Tremolo switch. ► While holding down the relevant switch (Key Transpose, Split, MIDI OUT, MIDI Lower, MIDI Upper, Receive Channel/Internal Voice Chorus or Tremolo), press the Pedal Switch. I 1—3 "j cww::,e*wc£ i Press the pedal While holding down. * When the pedal is used as a remote pedal, it does not function as a soft pedaf. If you wish to use it as a soft pedal, turn the RD-250s or RD-300s off once, then turn it on again. 17 ■ Sound Range Diagram RD-250S 442Hz T i i • MO CHANNEL- ■ PROGRAM CHANGE BANK 1~fl RD-300S 442Hz T PROGRAM CHANGE 18 ■ Setting Memo SET No. KEY TRANS. SPLIT ON/OFF LOW ch/SET MIDI ER pí:. OUT UPPE ch/SET •R P.C. VOICE IN CHORUS TERMAL VO TREMOLO RATE/OEPTH CE LOWER ON/OFF UPPER ON/OFF DEMO I C Ci 2/MKS2Q A 15 (CUV VI) l/EM 101 A H (Strings) E.PIAN01 ON OFF OFF ON DEM02 C OFF if A n (PÍANO 1) // A 25 (Flute) HARPSI OFF OFF OFF ON DEM03 C Ft OFF - // A 17 (Brass) PIAN03 ON OFF ON ON - - 19 Digital piano model RD-250s/300s MIDI Implementation Date : Aug. 20.-1937 Version : 1.0 TRANSMITTED ОЛТА Status Second Third 1001 nnnn Okkk kkkk ÛOOO 0000 1001 nnnn Okkk kkkk Ovvv wvv 1011 nnnn 0000 OUI Owv mv о О nnnn nnnn 0100 otoo 0000 0000 oui 0000 nu oooo 1011 toil nnnn nnnn 0100 0100 0010 0010 oui 0000 nu oooo О о nnnn nnnn otoo OlOO 00 M 0011 oui 0000 nu oooo ion 1011 nnnn nnnn 0101 0101 noo U00 OUI 0Q00 1 It 1 oooo о О nnnn nnnn Oîot OtOI 1 101 liot oui oooo nu oooo 1 100 * nnnn > ** ~ Oppp pppp 101 J toi 1 1011 nnnn nnnr» nnnn oui OUI 0111 1011 1100 ntt oooo 0000 oooo oooo oooo oooo Heu «r Mot« C* kkkkUkt 15 - 113/10-300* 22 - 10B/KD-ISO« 1 - 127 Volu loldl m Holdl OFF Soft m So ft OIF »2 If the power ha* been applied with the PIANO i avitch b«in| held doMtt, thlft is kihorcd. »3 Refer te 8. PROGRAM CHANGE IH RECEIVING. M Whan (hi AIL KOTES OFF la rccQiniied, all KIDt-on notes arc turned OFF. However« if the daaper pedal Is being pressed, the*« ON not«« will not be turned OFF until the daaper pedal is r«l«as«d. Similarly. if the MIDI Koldt OS ■«•«age has been received, the note« will not be turned off until Uic Koldt OFF oeaaage is received. CbMtv * в * 127 ALL HOTtS OFF OMNI OFF POLT m Active Sensing These Node Нее ta# es (2nd by le r eco« ni sed as the ALL NOTES OFF- 123 - 1271 «re also Messages are recognised as follow«; : POLY ON {1...