Votos - 5, Puntuación media: 3.4
(
)
)
|
Resumen del manual
. . First turn all knobs to the setting for normal sound. ©Set Reverb Volume to proper level. 0Set Input Volume to proper level. 0Set Treble and Bass controls to suit your taste. Reverb control adjusts the resonance effect to meet the room acoustics. The reverb effect can be added to all of normal sound, chorus and echo effects. ® TO PRODUCE ECHO EFFECT____ First turn all knobs to the setting for normal sound. ©Depress Echo switch and make sure Echo Effect indicating Lamp lights up. 0Set Input Volume to proper level. ©Set Echo Volume to proper level. • OSet Mode Selector to proper position to obtain the echo rate you hope to get. 0Adjust echo repetition with Echo Intensity, ©Further, fine-adjust echo rate with Repeat • Rate. ECHO ■ TO PRODUCE CHORUS EFFECT . . First turn all knobs to the setting for normal sound. © Depress Chorus switch and make sure Chorus Effect Indicating Lamp lights up. 0 Set Input Volume to proper level. ©Adjust chorus effect sound with Chorus Intensity control. Chorus effect changes normal sound to thick, unison sound. TO PRODUCE SINGLE DELAY . . . When you flip Single Delay switch down, single delay (one-time repeat} is obtained, irrespective of setting of Echo Intensity control. ■ TO PRODUCE SOUND ON SOUND EFFECT. . . . First turn all knobs to the setting for normal sound. © Set Sound on Sound switch to ON. 0 Set Input Volume to proper level. Sound on Sound effect reproduces input sound 10 — 30 seconds later to achieve doubled performance or to add another effect sound on the sound being performed. SI!VfGL-E DELAY CONNECTIONS CONfMECi IMG TO PA MIXER OR VOCAL IVIIXER Adjustment of echo effect (deepness) is made by Echo Volume on RE-301 and effect volume for each channel on the mixer. > Green H TO ECHO Red / FROM ECHO 1IMIIIIIII lllllllll ii iiiiiiiNi minim □ o □ 0 o O a O □ o Q o □ O a O □ o o o o o o o o o o o o o o o o oo i i A A I 1 IVIIXER RE-301 *Set Direct Sig. switch to OFF. —l£)r ooo OOOO 0 O O 0 0 0 009 OOOOO 0 90 INPUT OUTPUT Red ■ CONNECTING TO MICROPHONE, INSTRUMENT, ETC. ~* Set Direct Sig. switch to ON. o o o o ° o o o o 900 ooooo p o OPERATION 0 After completing connections, normally set Chorus Intensity, Echo Intensity, Echo Volume, Repeat Rate, Reverb Volume, Treble and Bass Controls to middle positions (12 o'clock) and Input Volume to extreme counterclockwise (O). ©Set Output Level Changeover switch to proper position to accord with the sensitivity of amplifier you use. a FOOTSWITCH FOOT VOLUME ©Set Direct Signal switch to ON. * When connecting to PA or vocal mixer, set to OFF. O’Set Chorus and Echo switches to OFF(J u—1_). OFF ON o (o ( o V AMPLIFIER * Set Sound on Sound switch to OFF whenever unnecessary. When using one amplifier, connect to "A" jack. -20-35 -50dB OMake sure that Power Switch is set to OFF. Then connect power and turn Power Switch on, and VU meter lamp will light up. «m a MUMS wipIIbWIvIK. ©Set each Input Level switch to proper position to accord with the output level of device you use. Normally, set to —50dB for microphone, —35dB for electric guitar and —20dB for synthesizer. #Turn Input Volume to proper level, and normal sound is produced. This setting of knobs is a basic smarting point to produce varied effect sounds. When operation is confused, turn back to this setting again. EFFECT SECTION LAMP lights up when Chorus switch is depressed to indicate that chorus effect is active. ■ CHORUS INTENSITY controls depth of chorus effect. Turn clockwise (O) to make deeper and counterclockwise (O) to make less deeper. is CHORUS SWITCH; When depressed, chorus effect goes into action and chorus effect indicating lamp lights up. To cancel, push this switch again. ® EFFECTS JACK: Connect footswitch FS-1. AH effects: echo, chorus, S. on m S. and reverb; of Input 3 can be on-off controlled remotely. OUTPUT SECTION A B A + B SOUND ON SOUND: When set to ON, input sound is reproduced 10 — 30 seconds later. You can double the performance or add another effect sound on your performance simply by handling this switch. * Be sure to set to OFF whenever unnecessary. « REMOTE JACK: Echo rate can be remote-controlled by foot volume (FV-2), which is very efficient for on-stage performance. Connect to output of foot volume. Treading deeper increases echo repeat rate and vice versa. CANCEL REMOTE SWITCH: Connect footswitch (FS-1) to respective jack. Chorus, echo effect or S. on S. can be remotely on-off controlled separately. ^ BASS controls volume of low frequency range of echo, chorus and reverb sounds. Turn clockwise (O) to boost and counterclockwise (O) to cut. h TREBLE controls volume of high frequency range of echo, chorus and reverb sounds. Turn clockwise (O) to boost and counterclockwise (O) to cut. ■ OUTPUT LEVEL CHANGEOVER. SWITCH: Set to either H, M or L to suit the amplifier you use. When connecting to guitar amplifier or microphone input on P...