Votos - 2, Puntuación media: 4.5
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
* Keep this unit horizontal when lifting it during assembly or transport. * Be careful not to pinch your hands or drop this unit on your foot during assembly or transport. * You must obtain the assistance of at least one additional person when assembling or transporting this unit. * Keep small parts such as screws out of the reach of small children to ensure that these items are not swallowed accidentally. * The screwdriver needed for assembly is not included. You will need to provide a Phillips screwdriver of the appropriate size for the screws. * You should initially tighten each screw loosely before tightening them to their final position. Start by tightening the screws until they are approximately half hidden. Do not use a power screwdriver when tightening the screws to their final position. Doing so may strip the threads. * Tighten the screws firmly, and place the unit at a location that is level and sure to remain stable. Never place the unit on a shag carpet. If you do so, the pedal may be unstable, causing damage. * Do not place the body of the piano directly on the floor. Doing so will damage the jacks and holders on the bottom of the piano, and also damage the bottom panel case. Copyright © 2011 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. 1 Music rest 2 Piano main unit 3 Side board (left) 4 Side board (right) 5 Rear board 6 Pedal board 2. Assembling the Piano 1. Align the screws on the bottom of the piano (one each at left and right) with the metal brackets on the side boards, and while keeping the front of the piano slightly raised, pull it toward yourself to engage the screws in the metal brackets. * When handling the piano, firmly grasp it. Be careful, so you do not get your fingers pinched. 2. Fasten the piano to the stand with the screw D (5 x 20 mm). Screw D Screw D Please don’t get your fingers pinched. Pull the piano toward yourself while keeping the front slightly raised. 3. Loosen the music rest screws slightly (2–3 mm), insert the music rest brackets between the screws and the body of the piano, and turn the screws to secure the music rest while using one hand to support the music rest. When attaching the music rest, make sure that it is firmly inserted all the way toward the back, and use your hand to support the music rest so that it does not fall. Also take care not to pinch your hand. * Do not apply excessive force to the music rest. * If you need to remove the music rest, loosen the screws while using one hand to support the music rest. Detach the music rest, and then firmly retighten the screws. 4. Connect the AC adaptor to the DC In jack on the back of the piano, and connect the pedal cord to the Pedal connector. As needed, use the coated clip on the bottom of the piano to fasten the power cord and the pedal cord. Coated clip 5. Use screws E (4 x 16 mm) to fasten the headphone hook. Screw E (2 pcs.) 6. Connect the supplied AC adaptor and power cord. Place the AC adaptor so the side with the indicator faces upwards and the side with textual information faces downwards. The indicator will light when you plug the AC adaptor into an AC outlet. To AC outlet Power cord 7. Adjust the Adjuster. Turn the adjuster to lower it until the adjuster is in firm contact with the floor. In particular, when you’ve placed the piano on carpet, you must turn the adjuster until it is pressing firmly against the floor. Adjuster * The pedal may be damaged if there is a gap between the adjuster and the floor. 1 2 3 4 5 6 A B C D E F Screw (4 . 14 mm): 2 pcs. Screw (4 . 20 mm): 4 pcs. Screw (5 . 40 mm): 4 pcs. Screw (5 . 20 mm): 2 pcs. Screw (4 . 16 mm): 2 pcs. Headphone hook: 1 pcs. 1. Stand Assembly * At first, assemble the entire stand in a temporary fashion, without really tightening the screws. Then, after checking the overall alignment of the boards (and gently shifting certain parts where necessary), go around and tightly fasten each of the screws. * If necessary, spread out a blanket or similar material to prevent the stand or floor from being scratched during assembly. * Be careful not to pinch the pedal cord during assembly. 1. As shown in the illustration, place the left and right side boards on the pedal board so that the metal brackets are on the inside, and fasten them provisionally using screws C (5 x 40 mm). 2. Hand-tighten screws C (four locations), and then use a screwdriver to tighten them securely. * When attaching the pedal board, do not allow any gap to remain between the side board and pedal board when the pieces are assembled. Side board Don’t allow a gap! Screw C (2 pcs.) Leave the pedal cord extended Screw C (2 pcs.) 3. With the help of another person, raise the left and right side boards to an upright position. * Take care that the pedal boards are not twisted. 4. Place the rear board as shown below and adjust the screw holes of the rear board and the pedal board. * If you ...