Votos - 5, Puntuación media: 3.6
(
)
)
|
Resumen del manual
Power is turned on whenever a plug is inserted into the INPUT jack, and is turned off when the plug is disconnected. When not using the unit, you should disconnect any cord connected to the INPUT jack. Balance Knob Control Knobs —-- BALANCE i DIR EFX mode" EFFECT Mode Switch BALANCE Knob This knob adjusts the balance (for the output) of the direct sound with respect to the effect sound. With the BALANCE knob at the center (click) position, the direct sound and effect sound will be in equal proportions (1:1 ratio). When turned all the way to the left, only the direct sound will be heard. Similarly, when turned all the way to the right, only the effect sound will be output. Control Knobs The two control knobs are used to make a variety of settings, depending on the mode you have selected. The sound obtained with a control knob will be different depending on the position of the MODE switch. For details, please refer to "Mode Chart." CHECK ......Q.......... TONÉ-R.TIME F.BACK D.TIME MODE 10 11 1-3 4-7 8-11 DELAY DELAY+REVERB REVERB! MODE Switch This knob is used to selected one of the RV-3's 11 modes. For information on each mode, please refer to "Mode Chart." Mode Chart DELAY 32-125 ms A delay with a delay time of 32 ms to 125 ms. DELAY 125-500 ms A delay with a delay time of 125 ms to 500 ms. 8 DELAY 500-2000 ms A delay with a delay time F.BACK Adjusts the amount of feedback. When you alter the feedback amount, the number of repetitions of the delay sound will change. of 500 ms to 2000 ms. Used to carry out precision adjustment of the delay time. The delay time will change within the selected range. OUTPUT A(MONOVB A mix of the direct sound and effect sound will be output from A and B (in accord with the setting of the BALANCE knob.) The output from A and B is identical. IT DELAY+REVERB: ROOM 1 Applies a small room reverb to the delay sound. * The Reverb Time is fixed. m DELAY+REVERB: ROOM 2 Applies a large room reverb to the delay sound. * The Reverb Time is fixed. □ DELAY+REVERB:HALL Applies a hall reverb to the delay sound. * The Reverb Time is fixed. a DELAY+REVERB:PLATE Applies a plate reverb (the reverberation obtained from the vibrations of a metal plate) to the delay sound. A metallic reverberation can be obtained. * The Reverb Time is fixed. ^^hf.backHHH ■ D.TIMEH OUTPUT A(MONO)/B Adjusts the amount of feedback in the delay sound. When you alter the feedback amount, the number of repetitions in the delay sound will change. Adjuststhedelaytime from 32 ms to 1000 ms. When you connect to OUTPUT A and B, the reverb sound will be output in stereo. Output of the delay sound will be the same as in modes 1-3. 9 8 ROOM 1 A reverb that simulates the reverberation within a room. 9 ROOM 2 A reverb that simulates the reverberation in a room that is more spacious than ROOM 1. 10 HALL A reverb that simulates the reverberation inside a hall. 11 PLATE A reverb that simulates a plate echo (reverberation obtained from the vibrations of a metal plate). Metallic reverberation can be obtained. TONE R.TIME OUTPUT A(MONO)/B Adjusts the tonal color (timbre) of the reverb sound. Adjusts the length (time) of the reverb sound. When you connect to OUTPUT A and B, the reverb sound will be output in stereo. 10 Making the Connections ii * The unit's output is muted for approximately 4 seconds after the power is turned on; no sound will be heard during this interval. * Inserting a plug into the INPUT Jack will automatically switch the unit on. * The use of an AC adaptor is recommended as the unit's power consumption is relatively high. Should you prefer to use batteries, please use the alkaline type. * Noise may be produced if wireless communications devices, such as cell phones, are operated in the vicinity of this unit. Such noise could occur when receiving or initiating a call, or while conversing. Should you experience such problems, you should relocate such wireless devices so they are at a greater distance from this unit, or switch them off. * To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections. * If there are batteries in the unit while an AC adaptor is being used, normal operation will continue should the line voltage be interrupted (power blackout or power cord disconnection). * Once the connections have been completed (p. 8), turn on power to your various devices in the order specified. By turning on devices in the wrong order, you risk causing malfunction and/or damage to speakers and other devices. When powering up: Turn on the power to your guitar amp last. When powering down: Turn off the power to your guitar amp first. * Always make sure to have the volume level turned down before switching on power. Even with the volume all the way down, you may still hear some sound when the power is switched on, but this is normal, and d...