Votos - 5, Puntuación media: 4
(
)
)
|
Resumen del manual
No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. 1 MIDI Implementation QAttack Time (Controller number 73) Status 2nd byte 3rd byte BnH 49H vvH n = MIDI channel number: 0H - FH (Ch.1 - 16) vv = Attack time value: 00H - 7FH (0 - 127) * The Amp Attack Time parameter will change. QCutoff (Controller number 74) Status 2nd byte 3rd byte BnH 4AH vvH n = MIDI channel number: 0H - FH (Ch.1 - 16) vv = Cutoff value: 00H - 7FH (0 - 127) * The Filter Cutoff parameter will change. QDecay Time (Controller number 75) Status 2nd byte 3rd byte BnH 4BH vvH n = MIDI channel number: 0H - FH (Ch.1 - 16) vv = Decay Time value: 00H - 7FH (0 - 127) * The Amp Decay Time parameter will change. QVibrato Rate (Controller number 76) Status 2nd byte 3rd byte BnH 4CH vvH n = MIDI channel number: 0H - FH (Ch.1 - 16) vv = Vibrato Rate value: 00H - 40H - 7FH (-50 - 0 - +50) * The Pitch Fine parameter of OSC2 will change. QVibrato Depth (Controller number 77) Status 2nd byte 3rd byte BnH 4DH vvH n = MIDI channel number: 0H - FH (Ch.1 - 16) vv = Vibrato Depth Value: 00H - 40H - 7FH (-50 - 0 - +50) * The Pitch Fine parameter of OSC1 will change. QVibrato Delay (Controller number 78) Status 2nd byte 3rd byte BnH 4EH vvH n = MIDI channel number: 0H - FH (Ch.1 - 16) vv = Vibrato Delay value: 00H - 7FH (0 - 127) * The PWM Depth parameter of OSC1 will change. QGeneral Purpose Controller 5 (Controller number 80) Status 2nd byte 3rd byte BnH 50H vvH n = MIDI channel number: 0H - FH (Ch.1 - 16) vv = Control value: 00H - 40H - 7FH (-64 - 0 - +63) * The Amp Depth parameter of LFO1 will change. QGeneral Purpose Controller 6 (Controller number 81) Status 2nd byte 3rd byte BnH 51H vvH n = MIDI channel number: 0H - FH (Ch.1 - 16) vv = Control value: 00H - 40H - 7FH (-64 - 0 - +63) * The Filter Envelope Depth parameter will change. QGeneral Purpose Controller 7 (Controller number 82) Status 2nd byte 3rd byte BnH 52H vvH n = MIDI channel number: 0H - FH (Ch.1 - 16) vv = Control value: 00H - 7FH (0 - 127) * The Filter Attack Time parameter will change. QGeneral Purpose Controller 8 (Controller number 83) Status 2nd byte 3rd byte BnH 53H vvH n = MIDI channel number: 0H - FH (Ch.1 - 16) vv = Control value: 00H - 7FH (0 - 127) * The Filter Decay Time parameter will change. QPortamento Control (Controller number 84) Status 2nd byte 3rd byte BnH 54H kkH n = MIDI channel number: 0H - FH (Ch.1 - 16) kk = source note number: 00H - 7FH (0 - 127) * A Note-on received immediately after a Portamento Control message will change continuously in pitch, starting from the pitch of the Source Note Number. * If a voice is already sounding for a note number identical to the Source Note Number, this voice will continue sounding (i.e., legato) and will, when the next Note-on is received, smoothly change to the pitch of that Note-on. * The rate of the pitch change caused by Portamento Control is determined by the Portamento Time value. QEffect 1 (Reverb Send Level) (Controller number 91) Status 2nd byte 3rd byte BnH 5BH vvH n = MIDI channel number: 0H - FH (Ch.1 - 16) vv = Reverb Send Level: 00H - 7FH (0 - 127) * In Performance mode the Part Reverb Send Level parameter will change. QEffect 3 (Chorus Send Level) (Controller number 93) Status 2nd byte 3rd byte BnH 5DH vvH n = MIDI channel number: 0H - FH (Ch.1 - 16) vv = Chorus Send Level: 00H - 7FH (0 - 127) * The Intensity parameter will change. QEffect 4 (Celeste) (Controller number 94) Status 2nd byte 3rd byte BnH 5EH vvH n = MIDI channel number: 0H - FH (Ch.1 - 16) vv = Celeste: 00H - 7FH (0 - 127) * The Effect Level parameter of Reverb/Delay section will change. QEffect 5 (Phaser) (Controller number 95) Status 2nd byte 3rd byte BnH 5FH vvH n = MIDI channel number: 0H - FH (Ch.1 - 16) vv = Phaser: 00H - 7FH (0 - 127) * The Bias of Filter Env Depth parameter will change. QRPN MSB/LSB (Controller number 100, 101) Status 2nd byte 3rd byte BnH 65H mmH BnH 64H llH n = MIDI channel number: 0H - FH (Ch.1 - 16) mm = upper byte (MSB) of parameter number specified by RPN ll = lower byte (LSB) of parameter number specified by RPN <<< RPN >>> Control Changes include RPN (Registered Parameter Numbers), which are extended parameters whose function is defined in the MIDI specification. When using RPNs, first the RPN (Controller numbers 100 and 101; they can be sent in any order) is transmitted to specify the parameter you wish to control. Then, Data Entry messages (Controller number 6 and 38) are used to set the value of the specified parameter. Once a RPN parameter has been specified, all further Data Entry message on that channel are considered to apply to parameter. In order to prevents accidents, when the desired setting has been made for the parameter, it is recommended that RPN be set to Null. 2 MIDI Implementation This device receives the following RPNs. RPN MSB, LSB 00H, 00H Da...