Votos - 4, Puntuación media: 3.3
(
)
)
|
Resumen del manual
Although they are not essential for a Pad setup, you should attach them as shown below so they do not get lost. To change the MDY-7U's angle, loosen the clamp. As your snare drum, use a PD-120. It can be mounted on your snare stand. Since the PD-120 has a diameter slightly smaller than an acoustic snare drum, some snare stands may not be able to hold it securely. When looking for a snare stand for the PD-120, select one that is designed to firmly hold a 12-inch diameter drum (like the PD-120). If this is not fixed firmly in place, double triggering may occur. Snare stand 5 Connections Before connecting anything, be sure that the power is OFF on all of the equipment in your système You risk damaging speakers or other equipment if you make connections while the power is ON. After everything has been connected, use the cable ties or clips (supplied with MDS-10) to fix the cables to the drum stand. * To prevent damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections. * For rim shots and choking, you loill need to connect the Pads to the TD-10 using the cables supplied with them (withstereo 1/4” phone plugs). 3/TOM 1 10/RIDE 7/HI-HAT TD-10 Stereo headphones to AC power outlet Stereo casette player, etc. Audio set, etc. Foot switches FS-5U 6 Assembling the V-Basic Kit (System Upgrade) The following introduces an example of how you could upgrade your system and get more out of the features available on the TD-10K/B. 8/CRASH 1 10/RIDE To install the new cymbal Pad(s), you will also need Cymbal Mount (MDY-7U). Assemble as follows. r , r V ...... =es ^ (29- =3^ 19 ft R R 7 Adjusting the head tension For the PD-100 and PD-120, adjustments are required in order to regularize the tension of the head. To make adjustments, you will need an acoustic drum tuning key (optional). * The PD-100 and PD-120 are shipped from the factory with the head tension loosened. Be sure to tighten the tension before use. Striking the head when the head tension is loose may damage the sensor. First, adjust the tension of the head of each PD-100/120. Then, once again adjust the tension of the PD-120 (SNARE) head for positional sensing. In general, a tension that produces a strike response approximately the same as an acoustic drum will be appropriate. 1. Strike the head to check the current tension of the head. 2. First adjust bolt ‘a’ in the above diagram. Rotate it clockwise to tighten the head tension, or slightly counterclockwise to loosen the tension. 3. Adjust bolt ‘b’ so that the tension is the same as the tension of ‘a’. 4. Next adjust ‘c’ and ‘d\ and ‘e’ and T in the same way. 5. Make sure that the head tension is even, and repeat steps 3 and 4 if you wish to make further adjustments. * On the PD-100/120, adjusting the head tension affects only the head response, and does not change the pitch of the sound as it would on an acoustic drum. To adjust the pitch, edit the sound parameters of the TD-10. For details refer to the TD-10 owner's manual. * The head tension will change as the instrument is used, so you should readjust when necessary. a c e Turning on the power * To prevent damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections, * If you run into problems, refer to the TD-10 owner's manual 1. Rotate [MASTER] and [PHONES] all the way to the left to turn down the volume. 2. Turn down the volume of the connected amp or audio system. 3. Turn on the POWER switch located on the rear panel of the TD-10. * When the power is turned on, the TD-10 will check the pads. If you touch the pads at this time, the check cannot be performed correctly. Do not strike pads or step on pedals until the following screen (the "DRUM KIT" display page) appears. UklUn K1 I Stud i oV GB9 cl (33 fx igr=l=M=fel 4. Turn on the power of the connected amp or audio system. 5. Raise the [GROUP FADERS] sliders to the maximum position, and adjust [MASTER] ([PHONES]) to the position shown in the diagram. ( : VOLUME CONTROL I »*■ PHONES ( j 6. While striking [PREVIEW] with your finger, adjust the volume of the connected amp or audio system. If you are using headphones, gradually raise [PHONES] to adjust the volume. The TD-10 will produce sound. The volume will depend on the force with which you struk [PREVIEW]. * You can use ITRIG SELECT] to select and audition the instrument for each pad. To turn the power off ... 1. Make sure that the TD-10 volume controls and the connected external devices are turned to the minimum position. 2. Turn off the power of the external devices. 3-Turn off the power of the TD-10. Trigger settings for the V-Basic Kit _ 1. Press [SETUP], press [F1 (TRIG)], and then press [F1 (BANK)]. 2. Use [CURSOR] to move the cursor to the “BANK” number. 3. Use [INC/DEC] or the VALUE dial to select “BANK 1.” □ TRIGGER SBDC KICK3...