Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Stereo headphones to AC outlet AC adaptor (indicator) Power cable 02 T3 T2 CR1 HH SNR HHC KIK TD-9 T1 RD RDB Align with indentation Check the included items TD-9KX Setup Guide ..Stand (MDS-9) ..Hi-hat mount Cymbal mount x 2 .. ..Cable tie x 6 Hi-hat control pedal (FD-8) .. Kick trigger pad (KD-8) .. Cymbal pad for hi-hat (CY-5) .. Cymbal pad for crash (CY-8) .. V-Cymbal for ride (CY-12R/C) .. V-Pad for snare (PD-105) .. V-Pad for tom (PD-85 x 3) .. Drum sound module (TD-9) .. Connection cable (special for TD-9) .. ..AC adaptor ..Drum key Assemble the stand Attach the parts D : Cymbal mounts E : Hi-hat mount A : Hand knobs B : Snare pipe C : Pad mounts If the stand wobbles, loosen this hand knob and adjust the height. As soon as you open the package, check to see that all items are included. If anything is missing, please contact your dealer. 1.2 m (48”) 135. 135. Connect the pads to the sound module Remove the screws Pull out the stand in the direction of the arrow, and use the screws you removed earlier to fasten the stand. Connect the cable to the TD-9 as shown in the illustration. 1. Connect the AC adaptor, and fasten it to the cable hook as shown in the illustration to prevent it from being accidentally unplugged. Labels indicating the 3. pad to be connected are attached to the cable. Make connections as shown in the illustration. 2. Connect the AC adaptor and speakers Wing nut Felt washer Tighten the wing nut to obtain an appropriate amount of sway. NOTE Attach the snare (PD-105) and toms (PD-85) Attach the hi-hat (CY-5) Attach the crash cymbal (CY-8) and ride cymbal (CY-12R/C) Assemble the kick (KD-8) Upper clutch Clutch felt (large) Lower clutch Clutch felt (small) While pressing Use drum key to tighten Attach the sound module (TD-9) 1 3 4 2 5 6 HEAD MADE BY REMO U.S.A. Tuning bolt Washer Hoop Gap Finger-tighten all six of the tuning bolts in the sequence shown in the illustration. The appropriate amount of tension is one that will provide approximately the same striking response as on an acoustic drum. Use the drum key to adjust the tension as needed. 1. 2. 3. Assemble the hi-hat control pedal (FD-8) Anchor bolt Shallower Deeper Slide the arm Attach the anchor bolt Adjusting the pedal depth (if installing on a drum mat) Anchor bolt Spring for the anchor bolt Loosen with the drum key, and tighten after adjusting Rod Rod Tighten Loosen Tighten Loosen Loosen the hand knobs (A, two locations) and spread open the left and right legs of the stand as shown in the illustration. 1. Adjust the pad mounts (C, four locations) as shown in the illustration. Loosen the hand knob of 3. the snare pipe (B), and pull out the snare pipe toward the side of the performer. 2. PD-105 PD-85 PD-85 PD-85 CY-8 CY-12R/C KD-8 FD-8 CY-5 TD-9 Attach the cymbal mounts (D, two locations) and hi-hat mount (E) as shown in the illustration. 4. BOW/EDGE output jack BOW/BELL output jack RD plug RDB plug Beater Install the kick pedal securely. Commercially available kick pedal Beater * Adjust the height so that the entire pedal comes into contact with the floor. This hight will vary depending on your kick pedal. When using on the drum mat When using on hard-surfaced flooring strikes the center of the head, then secure the kick pedal and KD-8 fi rmly in place. Attach the kick pedal Adjusting the foot plate height Depending on your kick pedal, it can be unstable when you attach it to the KD-8. Be sure to adjust the foot plate height so that the entire bottom surface of the pedal is attached to the fl oor. * Install the kick pedal securely. Take care not to pinch your fi ngers. The tips of the anchor bolts are sharp. Handle with care. When moving the KD-8, be sure to remove the screws and fold the stand. Transporting the KD-8 while it remains open may subject the stand to excessive strain and result in damage to the stand. Anti-skid tape is affi xed to the foot plate. When transporting the KD-8, don’t forget to pick up the foot plate. * * * * Loosen the stand’s anchor bolts * and remove the foot plate. Set the kick pedal so that the entire bottom surface is attached to the fl oor. 1. 2. In most cases, the stand becomes somewhat elevated. Tighten the anchor bolts securely there to fi x the stand and foot plate. 3. Adjusting the anchor bolts When using the kick pedal on a drum mat or similar surface, adjust the anchor bolts so their tips protrude from the plate. Then, secure the pedal in place; this will make it easier to use the kick pedal. However, when used on hard-surfaced fl ooring, the anchor bolts may damage the fl oor. Adjust the anchor bolts correctly. When using a twin pedal Position the two beaters equally apart from the center of the pad as shown in the fi gure at left. If one of the beater is further away from the center than the other, the sound from the further beater will be lower in volume, or will not sound as desired. Using a twin pedal will result in lower sensitivity as compared to when a single pedal is used. Raise the se...