Votos - 5, Puntuación media: 4
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
• Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. may injure your fingers. • Do not put your hands or feet under the foot pedal or foot switch. They may be pinched, resulting in injury. • Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged and drums may drop, causing injury. Digital Musical Instruments Division ©2011 Yamaha Corporation WW60710 110PO***.*01C0 WARNING CAUTION Assemble the RS700 Rack System. For details, refer to the assembly manual that came with the rack system. Check the contents of each package. Mount the pads and the drum trigger module on the rack system. As described below, mount the pads and the trigger module on the rack system, and then position the kick pad and the hi-hat. 1 2 . PCY135 Cymbal Pad (x2) . PCY155 Cymbal Pad (x1) . RHH135 Real Hi-hat Pad (x1) Package 1: DTP750C Package 2: DTP750P Package 3: DTX700 . Stand base for the RHH135 (x1) . CH750 Cymbal Holder (x2) . CH755 Cymbal Holder (x1) . HS650A Hi-hat Stand (x1) . Hi-hat clutch for the RHH135 (x1) . Cable band for the RHH135 (x1) . Stoppers for the PCY135 and PCY155 (x3) . Felts for the PCY135 and PCY155 (x3) . 10-channel snake cable (x1) . PCY100, PCY135, and PCY155 Owner’s Manual (x1) . RHH135 Owner’s Manual (x1) . Assembly Manual (this pamphlet) . Tuning key (x1) . Cable bands (x10) . DTX700 Owner’s Manual (x1) . DTX700 Data List (x1) . DVD (containing software) . DTX700 Drum Trigger Module (x1) . AC power adaptor* (x1) . Module stand (x1) . Module stand fastening screws (x4) . XP100SD Snare Pad (x1) . XP80 Tom Pad (x3) . SS662 Snare Stand (x1) . Clamp bolts (x4) . Clamp bolt S (x1) . KP65 Kick Pad (x1) . XP100T, XP100SD, XP120T, and XP120SD Owner’s Manual (x1) . XP70 and XP80 Owner’s Manual (x1) . KP65 Owner’s Manual (x1) * May not be included depending on your particular area. Please check with your Yamaha dealer. 3 Mounting the cymbal holders Mounting the tom pad 1. Mount the cymbal holders (CH750 x 2, CH755 x 1) on the rack system as shown below. CH750 CH750 CH755 1. Attach the clamp bolt to each of the tom pads and provisionally tighten (by 5 or 6 turns). 2. Mount the tom pads on the rack’s clamp rods. As shown below, ensure that the rod section is fully inserted into each pad’s mounting hole, and then fully tighten the clamp bolt. 3. If necessary, use clamp bolts A to E to adjust the height and angle of any of the pads. When doing so, be sure to adjust one bolt at a time (i.e., loosen a bolt, adjust the pad, and then retighten before loosening another). XP80 Clamp bolt (to be tightened in the direction shown) Tom pad (rear side) Tom pad Rod section Clamp bolt Insert Clamp rod Clamp bolt B Clamp bolt D Clamp bolt E Clamp bolt A Clamp bolt C Continued on other side Mounting the drum trigger module and cymbal pads . Mounting the drum trigger module 1. Attach the module stand (provided) to the underside of the drum trigger module using the module stand fastening screws. 2. Place the module stand inside the holder clamp and tighten the clamp bolt to secure in position. . Mounting the cymbal pads 1. Using a tuning key, loosen the stopper’s key bolt. 2. Remove the wing nut, the two felt pads, and the bolt cover from the cymbal holder. 3. Place the stopper on the cymbal holder. * If the key bolt was not sufficiently loosened in Step 1 above, it may not be possible to pass the stopper over the cymbal holder’s shaft. In such a case, loosen the key bolt as much as possible without removing it. 4. Replace the bolt cover. * When assembling the bolt cover, turn until it no longer rotates. 5. Secure the stopper in place. With the stopper making full contact with the bottom surface of the bolt cover, tighten the stopper’s key bolt using a tuning key. 6. Place one of the felt pads removed in Step 2 on the cymbal holder. 7. Mount the pad unit on the cymbal stand. Lower the pad unit into place with the cymbal holder’s shaft passing through the central hole of the cup section. When mounted, the stopper’s pin should rest inside the pad unit’s smaller hole. * If you were to play a cymbal pad without the stopper’s pin positioned inside the smaller hole, the pad could rotate, causing the cable to be pulled out. It is very important, therefore, to ensure that the stopper is secured as described in Step 5 above. 8. Assemble the felt pad that came with your pad unit. * The second felt pad removed from the cymbal holder in Step 2 above is not required for assembly of your pad unit. 9. Tighten the wing nut to secure the pad unit to the cymbal holder. PCY135 PCY135 PCY155 Drum trigger module Module stand fastening screws Module stand Drum trigger module (back side) Front of module Clamp bolt Drum trigger module + module stand Insert Holder clamp Tuning key Key bolt Stopper Cymbal holder Felt pads Bolt cover Wing nut Cymbal holder Stopper Bolt cover Cymbal holder Stopper Bolt cover Full contact Pad unit Felt pad that came with pad unit Cymbal holder Felt pad Bolt cover Pad unit Stopp...