Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
As shown in the illustration, remove the base attachment wing bolts, washers and spring washers (4 each) that are attached to the main body, and use those to attach the base to the main body. Only loosely tighten the wing bolts in this step. 2. Attach the foot pedal (FP6110, shown below) to the KP65. When attaching the pedal, make sure that the pedal's hoop clamp firmly clamps onto the ridge that runs across the front of the KP65's base. Rotate the T-handled bolt to the left to loosen the hoop clamp and to the right to tighten. 3. Adjust the base's position so that the DP65 pad's playing surface is vertical when the foot pedal is attached, and make sure that the KP65 is stable when the beater hits the pad. After the position is determined, firmly tighten the wing bolts to secure. 4. Adjust the pedal's position and the shaft length of the beater so that the foot pedal's beater hits in the center of the kick pad. Main Body Base Velcro Spring Washer Wing Bolt Washer Spur Hoop Clamp Beater T-Handlet Bolt Beater Beater (Double Foot Pedal) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 The PCY65 and KP65 are equipped with level adjustment knobs for adjusting the trigger output level. The pad's output level should be adjusted in regard to how hard you hit the pad when playing and the dynamic level which you require. Rotate the level adjustment knob to the right (+) to increase the output level, and to the left to decrease output level. ¦ Adjusting the Output Level (LEVEL): PCY65/KP65 NOTE: The KP65 can be configured with a double foot pedal (Yamaha DFP7210, etc., sold separately). When using a double foot pedal configuration, adjust the pedal's position and the length of the beaters so that the space between the two beaters is positioned in the center of the head. NOTE: If the product is set up on a special purpose drum riser, or if damage to the floor is not a concern, extend the foot pedal's spurs so that their points grip the riser or floor to prevent the KP65 from moving during performance. . FP6110 (Foot Pedal) The FP6110 foot pedal attaches to the KP65. First, assemble the pedal as shown in the illustration. 1. Insert the foot board stabilizer rods into the holes on the frame as shown in the illustration. 2. Attach the beater to the pedal as shown in the illustration, and use the beater fixing bolt to secure the beater in a suitable position. If necessary, carry out the adjustments described below. • Adjusting the Beater Angle Use a drum key (not supplied) to loosen the beater angle adjustment bolt and adjust the angle of the beater, then secure. 0 0 0 0 0 0 0 0 0 . KP65 LEVEL Adjustment Knob . PCY65 LEVEL Adjustment Knob • Adjusting the Spring Tension The recoil tension of the foot board is adjustable. • To increase spring tension, loosen nut A then tighten nut B shown in the illustration. • To decrease spring tension, loosen nut B shown in the illustration. Once the desired spring tension has been obtained,firmly tighten nuts A and B. NOTE: Adjust the level so that the DTXPLORER'S input level display registers 90-95% when you play ff (fortissimo : the loudest playing level). Please refer to the Owner's Manual that came with the DTXPLORER for more information. Too high of an output level setting will result in a narrow dynamic range (the difference between loud and soft) or may produce trouble such as double triggers (a single hit produces multiple sounds), etc. : Do not put excessive pressure on the level adjustment knob, it may result in damage. ¦ Specifications . PCY65 • Dimensions .............................. 312(W) X 245(D) X 46.5(H) mm • Weight .................................................. 620g • Sensor System ........................ Trigger Sensor (Piezo) x 1 • Output Jack ............. Standard Monaural Phone Jack . HH65 • Dimensions .............................. 142mm (W) X 398mm (D) X 104mm (H) • Weight .................................................. 1.5Kg • Sensor System ........................ Continuous Switch x1 • Output Jack .............................. Standard Stereo Phone Jack . TP65 • Dimensions ............. 220(diameter) X 61(H) (excluding the clamp bolt) • Weight ...................... 980g (including the clamp bolt) • Sensor System .......... Trigger Sensor (piezo-electric) x1 • Output Jack ............. Standard Monaural Phone Jack * Improvements may result in a change in the specifications and/or design of the product without notice. . KP65 • Dimensions ............. 233(W) x 271(D) x 416(H) mm (When Assembled) • Weigh ....................... 2.7kg • Sensor System .......... Trigger Sensor (Piezo) x 1 • Input Jack ................ Standard Monaural Phone Jack • Output Jack ............. Standard Stereo Phone Jack . FP6110 • Dimensions ............. 138(W) x 329(D) x 210(H) mm (when assembled: excludes beater) • Weight ...................... 1.2kg (includes beater) • Drive System ........... Belt • Beater ...................... Felt ¦ Replacing Wor...