Votos - 4, Puntuación media: 4.8
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
You can automatically adjust the various channel settings that best match your listening environment using the supplied optimizer microphone. Follow the procedure below to connect the optimizer microphone to this unit and place it in a proper location. Set the optimizer microphone at your normal listening position. Use the supplied cardboard microphone stand or a tripod to place the optimizer microphone at the same height as your ears would be when you are seated. Assemble the cardboard microphone stand and place the optimizer microphone on the top of the stand. Optimizer microphone (supplied) Cardboard microphone stand (supplied) If you have set the optimizer microphone, follow the steps on the backside to start the AUTO SETUP procedure. Continued on the back Connect the optimizer microphone to the OPTIMIZER MIC jack on the left side of this unit. 8 7 2b Printed in Malaysia WH90290 ..Do not plug the power supply cable into a wall outlet until all connections are complete. ..Unplug the power supply cable before changing connections, moving or cleaning this unit. .............. English Check the following points. ..Is the optimizer microphone firmly connected to this unit? ..Is the optimizer microphone placed in a proper loacation? ..Are there any large obstacles in between the optimizer microphone and the walls in your listening room? ..The AUTO SETUP procedure starts in 10 seconds after pressing ENTER on step 7. To achieve the best results possible, evacuate yourself for your listening room until the AUTO SETUP procedure is completed. ..To cancel the AUTO SETUP procedure after it is started, press RETURN. ..The AUTO SETUP procedure takes about 3 minutes. Press ENTER to start the AUTO SETUP procedure. The following screen appears on the TV and the AUTO SETUP procedure starts in 10 seconds. The setup screen automatically changes during the AUTO SETUP procedure. If any error occurs, the corresponding error message appears on the screen. In this case, see “Error messages for AUTO SETUP” on page 35 in the Owner’s Manual and then follow the instructions. To start the AUTO SETUP procedure once again, press RETURN and then carry out the procedure from step 5. When the AUTO SETUP procedure is complete, the following screen appears on the TV. * This is an example of the result screen. The result may differ depending on the environment. Press ENTER. The result is confirmed and the following screen appears on the TV for 2 seconds and then the menu screen disappears from the TV. The new settings are automatically saved in the system memory. Disconnect the optimizer microphone and keep it in a safe place. Enjoy TV or DVD audio in surround sound. For instructions on your TV or DVD player, refer to the owner’s manual supplied with each component. Before carrying out the procedure below, set the volume of this unit to 30. If necessary, adjust the volume level in step 4. Enjoying surround sound Carry out the AUTO SETUP (IntelliBeam) procedure to adjust the settings that best match your listening environment. This unit employs the YAMAHA IntelliBeam technology with the aid of the supplied optimizer microphone, allowing you to achieve highly accurate sound adjustments that best match your listening environment. Be advised that it is normal for loud test tones to be output during the AUTO SETUP procedure. Make sure that there are no children around in the listening room while the AUTO SETUP procedure is in progress. Press STANDBY/ON on the remote control. The power of this unit turns on. If a subwoofer with adjustable volume and crossover/high cut frequency controls is connected to this unit, set the volume between 11 and 1 o’clock as viewed on a conventional clockface and set the crossover/high cut frequency to the maximum. Turn on the power of your TV. Select the appropriate video input on your TV. Set the operation mode selector to YSP. Press and hold AUTO SETUP for more than 2 seconds. The menu screen appears on the TV. If the menu screen does not appear, check the video pin cable (connection 5 in the diagram on the front page) is connected properly and then press YSP followed by MENU. If you hear sound output from your TV speakers, turn down the volume level until you cannot hear any sound. Use the remote control supplied with your TV. Press VOLUME +/– on the remote control to adjust the volume level of this unit. Press one of the beam mode buttons on the remote control to select the desired beam mode. Select one of the three beam modes that best matches the current input source of this unit. For further information on the beam modes, see page 42 in the Owner’s Manual. To fine-tune the listening environment parameters manually or make advanced settings for speaker positions, sound beams, etc., see “MANUAL SETUP” on page 60 in the Owner’s Manual. VOLUME TV VOL MUTE TV INPUT TV MUTE CH STEREO MY BEAM SURROUND SPORTS 5BEAM ST+3BEAM 3BEAM MUSIC MOVIE 1 2 3 4 5 6 7 8 9 PREPARATION & CHECK Please connect the MIC. Please place t...