Votos - 4, Puntuación media: 4.5
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
It is normal for loud test tones to be output during the AUTO SETUP procedure. Make sure that there are no children around in the listening room while the AUTO SETUP procedure is in progress. 1. Place the IntelliBeam microphone at your normal listening position. Assemble the cardboard microphone stand and place the IntelliBeam microphone on top of it horizontally as shown below. Use the supplied cardboard microphone stand to place the IntelliBeam microphone at the same height as your ears would be when you are seated. Make sure that there are no obstacles between the IntelliBeam microphone and the walls in your listening room as these objects obstruct the path of sound beams. 4. Connect the IntelliBeam microphone to the INTELLIBEAM MIC jack on the rear of the unit. 2. Press the key on the remote control. The power of this unit turns on. 3. Turn the TV on and switch the TV’s input to display video content from this unit. When this unit is connected to the HDMI input on the TV (as shown in “Connecting a TV and a Blu-ray disc player” in this Quick Reference Guide), switch the TV’s input to “HDMI1”. You can select the language for the menu display. Press and hold the SETUP key until the “OSD LANGUAGE” menu appears. Press the ../.. key to select the desired language. Press the SETUP key again to exit the setup menu. 1 2 3 4 5 Remove Fit in Fit in Place horizontally Run through IntelliBeam microphone Upper limit Center height of this unit Within 1 m (3.3 ft) Within 1 m (3.3 ft) Listening position Cardboard microphone stand 1.8 m (6.0 ft) or more Lower limit Center line IntelliBeam microphone Cardboard microphone stand yTip AUTO SETUP (PREPARATION & CHECK) Please connect the MIC. Please place the MIC at least 1.8m/6ft away from Sound Projector. The MIC should be set at ear level when seated. Measurement takes about 3min. After [ENTER] is pressed, please leave the room. IntelliBeam microphone (supplied) [ENTER]:Start [RETURN]:Cancel Cardboard microphone stand (supplied) 5. Make sure that your listening room is as quiet as possible. For accurate measurement, turn off air conditioner or other devices that make noises. Follow the instructions below and then leave the room. If you remain in the room, you may obstruct the beam, or the microphone may pick up any sounds you make, possibly resulting in improper configuration of settings. When leaving the room, bring this Quick Reference Guide with you. The AUTO SETUP procedure takes about 3 minutes. Wait outside the room during the AUTO SETUP procedure. To cancel the AUTO SETUP procedure after it is started, press the RETURN key on the remote control. 6. Press the ENTER key to start the AUTO SETUP procedure and then leave the room within 10 seconds. The screen automatically changes during the AUTO SETUP procedure. If the AUTO SETUP procedure is complete, this unit rings the chimes and the results will be displayed on the TV. If “ENVIRONMENT CHECK:Failure” is displayed, see page 27 of the Owner’s Manual and run the measurement process again. • The results displayed depend on the position of the unit. • If you hear a buzzer sound and an error message appears on the TV, look for a solution in “If an error message is displayed” on page 27 of the Owner’s Manual. Then press the RETURN key to run the measurement process again. 7. Press the ENTER key. Measurement results are applied to this unit. • You can save the several measurement results pressing the SYSTEM MEMORY key (see page 28 of the Owner's Manual). 8. Remove the IntelliBeam microphone. Keep the IntelliBeam microphone in a safe place. The settings are automatically saved in the system memory. Note Will begin in 10 sec. Please leave the room ---------- AUTO SETUP START [RETURN]:Cancel (After 3 min.) ENVIRONMENT CHECK: Success BEAM MODE: 5Beam/Plus2 SHOW RESULT MESUREMENT COMPLETE. [ENTER]:Save set-up. [RETURN]:Do not save set-up. yTips AUTO SETUP COMPLETE Please remove the MIC from Sound Projector and the listening position. Press [SYSTEM MEMORY] key to save set-up in the memory. Installation Connection Settings Playback Playing back Confirm that this unit and other audio/video devices are properly connected by playing a DVD or BD on the Blu-ray disc player. The following explains the playback procedure when this unit, TV, and Blu-ray disc player are connected as shown in “Connecting a TV and a Blu-ray disc player” in this Quick Reference Guide. ¦ Enjoying TV in surround sound 1. Press the key to turn on this unit. 2. Turn on your TV and Blu-ray disc player connected to this unit. 3. Press the HDMI1 key to select the Blu-ray disc player as the input source. 4. Switch the TV’s input to HDMI 1. 5. Play back a DVD or BD on the Blu-ray disc player. 6. Press the VOLUME (+/-) key to adjust the volume. Use TV remote control to mute the sound from TV. 7. Press the SURROUND key and then the CINEMA DSP keys to set your sound preferences. When this unit does not play back, check the following • The connection between this unit and B...
Otros modelos de este manual:Instrumentos Musicales - YSP-3300 (650.91 kb)