Votos - , Puntuación media:
(
)
)
Fabricar: Yamaha
Tamaño del archivo: 1.69 mb
Nombre del archivo:
Idioma del manual:
El documento se está cargando, por favor, espere
 |
El documento se está cargando, por favor, espere
Resumen del manual
They will supply power to any component whenever this unit is turned on. The maximum power (total power consumption of components) that can be connected to these SWITCHED AC OUTLETS is 200 watts. OPKRATION _ -3,3' 1,6^ To play a source 1 VOLUME Set to the " oo " position. \l/ -□-POWER Select the source you want to listen to. INPUT CD TAPE 1 TUNER TAPE 2 \ PHONO DAT I AUX If you select turntable as an input source (PHONO position), refer to “Setting the PHONO switch ” on the page 7. 4 Select the speaker system to be used by pressing the SPEAKERS switches. (Refer to the next page for details.) the source. VOLUME Adjust to the desired output level. If desired, adjust the BASS, TREBLE, BALANCE and LOUDNESS controls, etc. (Refer to the next page for details.) To record a source to tape (or dub from a tape to another) ^ Select the source to be recorded. REC OUT TAPE COPY «-□ATe-1/2- AUX- Play the source. Confirm the source by selecting it with the INPUT selector and turning up the VOLUME control. ¿il, Set the tape deck (or DAT) in the recording mode. If your tape deck has three head monitoring capability, you can monitor the signal just recorded by selecting the corresponding tape deck. INPUT CO TAPE 1 ^=5^ TUNER Also, refer to the manual of the tape deck being used. Notes • If you want to enjoy another source while recording, select it with the INPUT selector. • Adjusting the VOLUME, LOUDNESS, BASS, TREBLE, BALANCE controls and PURE DIRECT switch during recording has no effect on the material being recorded. Selecting the SPEAKER system Because one or two speaker systems can be connected to this unit, the SPEAKERS switches allow you to select speaker system A or B or both at once. Selling ihe IMIOVO Nwilch , _____________ Select either MM or MC position depending on your PHONO cartridge, Moving Magnet or Moving Coil type. However, if you use a high output MC cartridge, select the MM position. PHONO A SPEAKERS B 4b MC GN A ON || jl l| [l l| OFF A OFF in* the 3» \J. \\< I-' ron!nil Adjust the balance of the output volume to the left and right speakers to compensate for sound imbalance caused from the speaker settings or the listening room condition. Setting the SI BSONIC FILTER switch if you set the switch to the ON position, ultra-low-frequency signals caused by turntable rumble or warped records can be cut out without losing sound quality. Adjusting the BASS and TREBLE controls -5 5 + Setting the MODE switch This switch can be used for switching between stereo and monaural operation. Normally this switch should be set to the STEREO position. BASS: Turn this clockwise to increase (or counterclockwise to decrease) the low frequency response. TREBLE: Turn this clockwise to increase (or counterclockwise to decrease) the high frequency response. ENGLISH Adjusting the continuous LOrONESS control I sins the PURE DIRECT switch This control provides compensation for the human ears' loss of sensitivity to high and low-frequency ranges at low volume. This control is adjustable to retain full tonal range at any volume level. You can enjoy purer source sound by setting this switch so that the indicator illuminates. Because, by doing so, the input signal is output directly, bypassing the BASS, TREBLE, BALANCE, LOUDNESS controls, SUBSONIC FILTER, MODE switches and PRE OUT/MAIN IN terminals, therefore avoiding any “muddying” caused by circuit routing. LDUONESS FLAT Set to the “FLAT” position. □ PURE DIRECT Set to the loudest listening level that you would listen to. LOUDNESS FLAT Turn so that the desired volume level can be achieved. When you listen with headphones Connect the headphones to the PHONES jack. When listening with the headphones privately, set both the SPEAKERS A and B switches to the OFF position. PHONES {KMOTK-CONTROL TRANSMITTK Jl The remote-control transmitter provided with this unit is designed to control all the most commonly used functions of the unit. If the CD player, turntable, equalizer, tuner, and tapedeck connected to this unit are YAMAHA components designed for remote control compatibility (components with an mm mark), then this remote-control transmitter will also control various functions of each component. Please consult YAMAHA dealer for information on which components are compatible with the remote-control transmitter. 2 a n ■ ■ KEY FUNCTIONS For Amplifier Control Selects input source. EG EQ PKESETSK/P OWLAT EU CZ3 PLAY/CUT CH PHONO 1=1 — PRESET, -f- A/BOO/E □ □ □ TUNEH cm KKJ SKIP OCSH PLAY □ cm cm « SEAFOt 1» PAUSE/STOP □ □ □ CD cm DISC SKIP cm □IRA DECKAiB DIRB □ [=□ [=□