Iniciar sesión:
Votos - 3, Puntuación media: 3.7 ( )

Manual de usuario Yamaha, modelo AX-9

Fabricar: Yamaha
Tamaño del archivo: 163.13 kb
Nombre del archivo:
Idioma del manual:en
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


Make sure that the polarity of the speaker wires is correct, that is, + and – markings are observed. If these wires are reversed, the sound will be unnatural and will lack bass. Do not let the bare speaker wires touch each other and do not let them touch the metal parts of this unit as this could damage this unit and/or speakers. How to Connect: Red: positive (+) Black: negative (–) 123 . Unscrew the knob. . Insert the bare wire. [Remove approx. 5mm (1/4”) insulation from the speaker wires.] . Tighten the knob and secure the wire. . One or two speaker systems can be connected to this unit. If you connect only one speaker system, connect it to either the SPEAKERS A or B terminals. . Use speakers with the specified impedance shown on the rear of this unit. . Banana Plug connections are also possible. Simply insert the Banana Plug connector into the corresponding terminal. IMPEDANCE SELECTOR switch Be sure to switch this only when the power to this unit is not on. Select the position whose requirements your speaker system meets. WARNING Do not change the IMPEDANCE SELECTOR switch setting while the power to this unit is on, otherwise this unit may be damaged. IF THIS UNIT FAILS TO TURN ON WHEN THE STANDBY/ON SWITCH IS PRESSED The IMPEDANCE SELECTOR switch may not be set to either end closely. If so, set the switch to either end closely. (General model) IMPEDANCE SELECTOR SET BEFORE POWER ON A OR B:4WMIN./SPEAKER A OR B:8WMIN./SPEAKER A + B:8WMIN./SPEAKER A + B:l6WMIN./SPEAKER (Left position) If you use one pair of speakers, the impedance of each speaker must be 4W or higher. If you use two pairs of speakers, the impedance of each speaker must be 8W or higher. (Right position) If you use one pair of speakers, the impedance of each speaker must be 8W or higher. If you use two pairs of speakers, the impedance of each speaker must be 16W or higher. ABOUT THE ACCESSORY TERMINALS 1 AC OUTLET(S) (SWITCHED) (Europe and General models) * .......................................................... 3 SWITCHED OUTLETS (U.K. model) ........................................ 1 SWITCHED OUTLET Use these to connect the power cords from your components to this unit. The power to the SWITCHED outlets is controlled by this unit’s STANDBY/ON switch or the provided remote control transmitter’s POWER key. These outlets will supply power to any component whenever this unit is turned on. The maximum power (total power consumption of components) that can be connected to the SWITCHED AC OUTLET(S) is 100 watts. GND terminal (For turntable use) *2 Connecting the ground wire of the turntable to this terminal will normally minimize hum, but in some cases better results may be obtained with the ground wire disconnected. CONTROLS AND THEIR FUNCTIONS FRONT PANEL 123456 7 8 STANDBY/ON SLEEP TAPE MONITOR PURE DIRECT PHONES SPEAKERS ON OFF A B ON OFF PURE DIRECT TAPE MONITOR BASS TREBLE BALANCE L R 0 VOLUMEINPUT 0 l0 CDMDTAPE TUNERAUX –– + + PHONO 0 NATURAL SOUND STEREO AMPLIFIER AX 9l 90A BC 1Power indicator Lights up while the power to this unit is on. 2STANDBY/ON switch Press this switch to turn the power to this unit on. Press it again to turn this unit into the standby mode. Standby mode In this state, this unit consumes a very small quantity of power to receive infrared-signals from the remote control transmitter. 3Remote control sensor Receives signals from the remote control transmitter. 4SLEEP indicator Lights up while the built-in SLEEP timer is functioning. 5PURE DIRECT indicator Lights up while the PURE DIRECT switch is on. 6TAPE MONITOR indicator Lights up while the TAPE MONITOR switch is on. * When the tape deck (TAPE) is selected as the input source, this indicator will not light up even if the TAPE MONITOR switch is on. 7INPUT selector and indicators When turned, selects a program source to listen to. The indicator for the currently selected source lights up. 8VOLUME control Used to raise or lower the volume level. 9Control door See page 12 for how to open and close the control door. DE 0PHONES jack PHONES When you listen with headphones, connect the headphones to the PHONES jack. When listening with headphones privately, set both the SPEAKERS A and B switches to the OFF position. ASPEAKERS switches Set the switch A or B (or both A and B) for the speaker system (connected to this unit) you will use to the ON position. Set the switch for the speaker system you will not use to the OFF position. BPURE DIRECT switch You can enjoy the purest possible sound from your audio sources by pressing this switch so that the PURE DIRECT indicator lights up. By doing so, the audio signal bypasses the BASS, TREBLE and BALANCE controls, eliminating any alterations to the audio signal. CTAPE MONITOR switch When the tape deck connected to the TAPE terminals on the rear of this unit is used for recording, you can monitor the sounds being recorded by pressing TAPE MONITOR so that TAPE MONITOR indicator lights up. DTone controls BASS U...


Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría