Votos - 2, Puntuación media: 5
(
)
)
|
Resumen del manual
1. CENTER SPEAKER 2. REAR SPEAKER 3. MAIN SPEAKER 4. LFE/BASS OUT DESCRIPTION OF EACH FUNCTION 1. CENTER SPEAKER (CNTR SP) Choices: NRML/WIDE/PHNTM Preset position: NRML NRML (Normal): Select this position when you use a center speaker that is smaller than the main speakers. In this position, low bass signals (below 90 Hz) at the center channel are output from the MAIN output jacks (or the SUBWOOFER output jack if the SMALL position is selected on “3. MAIN SPEAKER” and the SWFR position is selected on “4. LFE/BASS OUT”). WIDE: Select this position when your center speaker is approximately the same size as the main speakers. PHNTM (Phantom): Select this position when you do not have a center speaker. The center channel sound will be output from the left and right main speakers. 2. REAR SPEAKER (REAR SP) Choices: SMALL/LARGE Preset position: SMALL SMALL: Select this position if your rear surround speakers do not have a high ability for bass reproduction. In this position, low bass signals (below 90 Hz) at the rear surround channels are output from the SUBWOOFER output jacks (or the MAIN output jacks if the MAIN position is selected on “4. LFE/BASS OUT”). LARGE: Select this position if your rear surround speakers have a high ability for bass reproduction, or a subwoofer is connected to the rear surround speaker in parallel. In this position, full range signals are output from the SURROUND output jacks. English 3. MAIN SPEAKER (MAIN SP) Choices: SMALL/LARGE Preset position: LARGE SMALL: Select this position if your main speakers do not have a high ability for bass reproduction. However, if your system does not include a subwoofer, do not select this position. In this position, low bass signals (below 90 Hz) at the main channels are output from the SUBWOOFER output jack (if the SWFR or BOTH position is selected on “4. LFE/BASS OUT”). LARGE: Select this position if your main speakers have a high ability for bass reproduction. In this position, full range signals present at the main channels are output from the MAIN output jacks. 4. LFE/BASS OUT (LFE/BASS) Choices: MAIN/SWFR/BOTH Preset position: SWFR MAIN: Select this position if your system does not include a subwoofer. In this position, full range signals present at the main channels, signals from the LFE channel and other low bass signals that are selected on “1. CENTER SPEAKER” to “3. MAIN SPEAKER” to be distributed from other channels are output from the MAIN output jacks. SWFR/BOTH: Select either the SWFR or BOTH position if your system includes a subwoofer. In either position, signals at LFE channel and other low bass signals that are selected on “1. CENTER SPEAKER” to “3. MAIN SPEAKER” to be distributed from other channels are output from the SUBWOOFER output jack. When the LARGE position is selected on “3. MAIN SPEAKER”, in the SWFR position, no signal is distributed from the main channels to the SUBWOOFER output jack, however in the BOTH position, low bass signals from the main channels are output to both of the MAIN and the SUBWOOFER output jack. METHOD OF CHANGING SELECTIONS Operations should be made watching information on this unit’s display panel. 3. Press “+” or “–” once or more so that the desired position is selected. 1. Turn the power of this unit on. PARAMETER POWER DVD/LD 2. Press “ ” or “ ” once or more until the title of function on which you will change the selection appears on the display. 4. Repeat step 2 and 3 to change selections on other functions in the same way. SET MENU DVD/LD OUTPUT BALANCE ADJUSTMENT Adjusting the output level balance among all the channels are very important to maximize the performance of your system including this unit. This unit lets you adjust the sound output level balance among the left main, center, right main, right surround and left surround channels using the built-in test tone generator. If your amplifier (or receiver) connected with this unit is equipped with the Dolby Pro Logic Surround Decoder, you should make the output balance adjustment for Dolby Pro Logic on the amplifier (or receiver) connected with this unit, before making the adjustment on this unit. Follow the instructions below. BEFORE MAKING THE ADJUSTMENT ON THIS UNIT Be sure to adjust the output level balance among the left main, center, right main and surround channels for Dolby Pro Logic on the amplifier (or receiver) connected to this unit using a test tone generator built into the amplifier. Adjust the balance so that the levels of those channels become almost the same when you hear the test tone at the listening position. If you have finished adjusting the output balance on the amplifier, then go on to the adjustment on this unit by following the procedure below. 1. Turn down the volume to a minimum level on the amplifier or receiver. 2. Press the TEST switch. TEST 3. Turn up the volume on the amplifier or receiver. You will hear a test tone (like pink noise) from the left main speaker, then the center speaker, then the right main s...