Votos - 10, Puntuación media: 4.3
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
02R Wordclock Setup On the DIGITAL I/O menu, the wordclock source should be set to W.CLK. ADAT & BRC Wordclock Setup The BRC works as wordclock master and the ADAT locks to it automatically via the 9-pin sync cable. The sampling rate can be set to either 48 kHz or 44.1 kHz. Notes • The ADAT must be powered up before the BRC, because when the BRC is powered up it checks how many ADATs are connected, allocates them device numbers, and automatically sets the system wordclock. • On the BRC, set the Clock Source to Internal. Setting it to SMPTE may cause noise. • To generate timecode on the BRC, press the GEN SYNC button. • On the BRC, set the DIGITAL I/O button to OFF. This function is for direct ping-pong between multiple ADATs. If this is turned ON while connected to an 02R, bus assignments will produce unexpected results. Press the DIGITAL IN button on the ADAT to use the DIGITAL INPUT. Yamaha 02R & 03D Applications Guide 02R Applications 43 Video machine ADAT TC DIGITAL IN=ON DIGITAL OUTPUT TV Monitor BRC Settings: Locate Reference=SMPTE Clock Source=Internal Ext Sync=ON TC=as required SMPTE Start Offset=as required Press GEN SYNC to output SMPTE timecode or MTC DIGITAL INPUT SYNC IN 9-pin cable Power Amp SYNC OUT BRC 00.00.00.00 GEN SYNC=ON DIGITAL I/O=OFF SMPTE timecode or MTC Optical cable DAT Recorder SMPTE IN DAT (phone jack) WC OUT SMPTE OUT (BNC) C-R Out 2TR IN DIGITAL CD8-AT 1 Interface Card SMPTE TIMECODE INPUT (phono) STEREO OUT DIGITAL DIGITAL RECORDING CONSOLE WORDCLOCK IN (BNC) (75.=ON) Headphones Figure 16 02R with Video Machine, ADAT, & BRC 02R Yamaha 02R & 03D Applications Guide 44 02R Applications 17 17 02R with Video Machine, ADAT, & AI-2 This application shows how the 02R can be used with a video machine, ADAT, and AI-2 Multipurpose Audio/Video Synchronization Interface for audio post-production and audio sweetening, with 02R automation. Using only the SMPTE timecode from the video machine, the AI-2 can generate both timecode (SMPTE or MTC) and wordclock for the ADAT and 02R. A timecode offset can be specified on the AI-2. Connections • The ADAT (CD8-AT) card must be screwed securely in place. Do not leave the screws out after installation as the cards will not be grounded correctly. • The Digital In/Out connectors on the 02R and ADAT are connected together using Optical Cables. Press the DIGITAL IN button on the ADAT to use the DIGITAL IN. • The ADAT’s eight tracks connect to 02R slot [1], tape inputs one through eight. • A 9-pin Sync cable for connecting the ADAT and AI-2 is available from Alesis. • The 75 ohm wordclock termination switch on the back of the 02R is set to ON. 02R Wordclock Setup On the DIGITAL I/O menu, the wordclock source should be set to W.CLK. ADAT & AI-2 Wordclock Setup The AI-2 works as wordclock master and the ADAT locks to it automatically via the 9-pin sync cable. The AI-2 sampling rate should be set to match that of the ADAT tape. Notes • On the AI-2, set the ONLINE Key for chasing. Yamaha 02R & 03D Applications Guide 02R Applications 45 Video machine DAT DIGITAL RECORDING CONSOLE 1 ADAT TC RDR IN (phone jack) TV Monitor DIGITAL IN=ON 9-pin cable SMPTE timecode or MTC Optical cable SMPTE TIMECODE INPUT (phono) CD8-AT Interface Card 2TR IN DIGITAL STEREO OUT DIGITAL C-R Out Power Amp DAT Recorder SYNC IN SYNC OUT GEN OUTWC OUT (BNC) WORDCLOCK IN (BNC) (75.=ON) DIGITAL OUTPUT DIGITAL INPUT Headphones AI-2 Settings: Online=ON TC=as required SMPTE Start Offset=as required Sampling rate=same as Adat tape AI-2 Figure 17 02R with Video Machine, ADAT, & AI-2 02R Yamaha 02R & 03D Applications Guide 46 02R Applications 18 18 02R with Video Machine & DA-88 This application shows how the 02R can be used with a video machine and DA-88 for audio post-production and audio sweetening, with 02R automation. Using only the SMPTE timecode from the video machine, the DA-88 can generate timecode (SMPTE or MTC) for the 02R. A timecode offset can be specified on the DA-88. Connections • The Tascam (CD8-TD) card must be screwed securely in place. Do not leave the screws out after installation as the card will not be grounded correctly. • The Tascam digital audio cable (PW-88DL) carries the eight tape sends and eight tape returns. • The DA-88 is connected to Slot [1] of the 02R. These tape inputs correspond to tracks one through eight. • The optional SY-88 Sync Board is required. The DA-88 has a dedicated timecode track and can output SMPTE timecode or MTC. In addition, a timecode offset can be specified on the DA-88, so the 02R automix start time can be adjusted. The DA-88 also has the ability to re-stripe the timecode track. • The video house sync is connected to the Video In BNC connection on the DA-88. 02R Wordclock Setup The 02R works as a wordclock slave. A Tascam (CD8-TD) card is installed in Slot [1], so any one of the first 8 tape inputs can be selected as the wordclock source on the DIGITAL I/O menu. DA-88 Wordclock Setup The DA-88 generates a wordclock signal referenced to th...
Otros modelos de este manual:Instrumentos Musicales - 02R (2.32 mb)