Votos - 4, Puntuación media: 4.3
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
Before you start updating the firmware, decompress the downloaded compressed file. Place “RIO_PROG.bin,” “update.exe” and “update.ini in the same folder. For information about messages displayed by the Rio firmware update program, refer to “Error Message List (Rio Update Program)” at the end of this guide. . Before starting the update program, quit all other programs. While the update is in progress, do not start any other programs or switch between windows. . If your computer enters Sleep or Energy Save mode, data transfer to the device may stop. Therefore, you should disable these functions to prevent this from happening. We also recommend that you do not use any screen saver or similar background programs. 1. Turn off the power to the Rio. 2. Take note of the dip switch settings on the Rio unit front panel. Follow the procedure below to change dip switch settings. Take note of the original dip switch settings in order to restore the settings when the Dante firmware update is completed. 3. Disconnect the Ethernet cable from the Dante [PRIMARY] connector and [SECONDARY] connector on the rear panel of the Rio unit. 4. Pull the dip switch 4 on the Rio unit front panel down (ON) and turn the power on with the other switch remaining in up their positions (OFF). 5. After the orange [SYNC] indicator flashes twice periodically on the front panel of the Rio unit, turn off the power. 6. Connect the Dante [PRIMARY] connector on the rear panel of the Rio unit to the Ethernet connector on the computer using an Ethernet cable. 7. Pull the dip switch 4 and 8 on the Rio unit front panel down (ON) and turn the power on with the other switch remaining in up their positions (OFF). The all +48V indicators start flashing and the unit is activated in the update mode. 8. Double-click [update.exe]. The Rio Update Program will start up. Make sure that the fields in the "File" section indicate as follows: file name :RIO_PROG.bin product name :CL_Rio Version :Version number to which the firmware will be updated .When running under Windows 7, the "User Account Control" dialog box may appear. Click [Continue] or [Yes]. 9. Click the [Connection] button in the “Connect and Update” column. The “product name” field will display “CL_Rio,” and the “version” field will display the version number of the Rio firmware. .If these fields are empty, your computer may not be properly connected to the Rio. Please make sure that the cable is not disconnected or damaged, that the TCP/IP settings are correct, and that the Rio has started in Update mode. 10. Click the [Update] button in the “Connect and Update” column. The update operation will begin. The update will take about 30 seconds. During the update operation, do not turn off the power to the unit or disconnect the cable. If update fails due to disconnection of the power cable during the update, or due to other reasons, the device may become inoperative. 11. When the “Connect and Update” section displays the message “Updating was completed. Close this Update Program” click the [X] button in the upper-right corner of the program window to close the program. 12. Turn of f the power to Rio. ¦ Computer TCP/IP setting (for Dante) To update Dante firmware, configure computer TCP/IP settings. Windows 7 1. Select [Start]>[Control Panel], then click or double-click [Network and Sharing Center] or [View network status and tasks]. The “Network and Sharing Center” is displayed. 2. Click [Manage network connection] or [Change Adapter settings] from the “Tasks” list located in the left side of “Network and Sharing Center” window, then double-click [Local Area Connection]. The "Local Area Connection Status" dialog box will be displayed. .The "User Account Control" dialog box may appear. Click [Continue] or [Yes]. .If the "Local Area Connection properties" dialog box appears, skip ahead to step 4. 3. Click [Properties]. The “Local Area Connection properties” dialog box will be displayed. .The "User Account Control" dialog box may appear. Click [Continue] or [Yes]. 4. Select [Internet Protocol Version 4 (TCP/IPv4)], then click [Properties]. The "Internet Protocol Version 4(TCP/IPv4) Protocol" dialog box will be displayed. 5. Click [Obtain an IP address automatically]. 6. Click [OK]. Windows XP 1. Select [Start] > [Control Panel]. The "Control Panel" is displayed. 2. If the control panel appears as category view, click [Switch to Classic View]. 3. Double-click [Network Connections] > [Local Area Connection]. The "Local Area Connection Status" dialog box will be displayed. .If the "Local Area Connection properties" dialog box appears, skip ahead to step 5. 4. Click [Properties]. The "Local Area Connection Properties" dialog box will be displayed. 5. Select [Internet Protocol (TCP/IP)], then click [Properties]. The "Internet Protocol (TCP/IP) Properties" dialog box will be displayed. 6. Click [Obtain an IP address automatically]. 7. Click [OK]. ¦ Updating the Dante firmware Described below are the procedures to up...
Otros modelos de este manual:Instrumentos Musicales - Rio1608-D (447.84 kb)