Votos - 1, Puntuación media: 3
(
)
)
|
Resumen del manual
See the figure on the right for wiring. J ST2 OUT jacks These unbalanced phone jacks output ST bus signals, with a nominal output level of +4 dB. See the figure on the right for wiring. K MATRIX OUT jacks 1/2 These unbalanced phone jacks output Matrix 1/2 signals that are a mix of MIX buses 1–4 and ST bus, with a nominal output level of +4 dB. See the figure on the right for wiring. Tip (send) Sleeve (ground) Tip (send) 1/4" phone plug Sleeve (ground) 1 (ground) Male XLR plug 3 (cold) 2 (hot) Tip (send) 1/4" phone plug Sleeve (ground) Tip (send) 1/4" phone plug Sleeve (ground) MC32/12, MC24/12—Owner’s Manual 18 Rear Panel 18 Rear Panel These TRS phone jacks are used to insert an external processor into the ST bus, with nominal input/output levels of 0 dB. See the figure below for wiring. 1/4" phone plug 1/4" phone plug 1/4" TRS phone plug To processor’s input From processor’s output Connect to INSERT I/O jack Tip (send) Tip (send) Ring (return) Sleeve (ground) Sleeve (ground) Tip (return) Sleeve (ground) M C-R MONITOR OUT jacks These unbalanced phone jacks are used to monitor input signals sent from the PFL bus, AFL bus, and TAPE IN jacks, with a nominal output level of +4 dB. See the figure on the right for wiring. Tip (send) N TAPE IN jacks These unbalanced phono jacks are used to connect a line-level device, with a nominal input level of –10 dBV. See the figure on the right for wiring. Phono plug Tip Sleeve O REC OUT jacks These unbalanced phono jacks output line-level, pre-fader, pre- insert I/O ST bus signals. See the figure on the right for wiring. Phono plug Tip Sleeve 1/4" phone plug Sleeve (ground) MC32/12, MC24/12—Owner’s Manual GA Diversity Function 19 GA Diversity Function 19 GA Diversity is an output select function that allows you to use the MIX OUT jacks as group output jacks or AUX output jacks on the MC32/12 and MC24/12. You can route either MIX (Variable) bus signals or MIX (Fix) bus signals to the MIX OUT 1–4 jacks of the MC32/12 and MC24/12. You can select either one of these output signals in the Variable/Fix select section. If the M1–M4 switches in the Variable/Fix select section are set to FIX ( ), the corresponding MIX OUT jacks will output MIX (FIX) bus signals. Since each channel’s output level for the MIX (FIX) bus signals is fixed, the corresponding MIX OUT jacks will function as group output jacks. If the M1–M4 switches in the Variable/Fix select section are set to VARIABLE ( ), the corresponding MIX OUT jacks will output MIX (VARIABLE) bus signals. Since each channel’s output level for the MIX (VARIABLE) bus signals is variable, the corresponding MIX OUT jacks will function as AUX output jacks. The GA Diversity function will enable you to configure a flexible bus system, such as four groups and six AUX sends, two groups and eight AUX sends, or 10 AUX sends, etc., depending on the application. VARIABLE/FIX FIX MIX OUT 1 MIX INSERT I/O 1 to MTRX PFL PAN CTLRL to AFL RL ST TO ST AFL HIGHLOW fg MID 3-Stage EQ EQ 109876512344321 MIX (VARIABLE) MIX (FIX) Setting the GA Diversity function 1. Press down the M1 switch ( FIX) in the Variable/ Fix select section (see page 6). The FIX indicator will light up. The MIX OUT 1 output channel will receive the MIX (FIX) 1 bus signal, and the MIX OUT 1 jack will function as a group output jack. 2. Press the M1 switch again to set it to ( VARIABLE). The FIX indicator will be turned off. The MIX OUT 1 output channel will receive the MIX (VARIABLE) 1 bus signal, and the MIX OUT 1 jack will function as an AUX output jack. 3. Set the M2, M3, and M4 switches in the same way. You can set MIX OUT 1–4 channels to “FIX” or “VARIABLE” individually. VARIABLE / FIX M1 FIX M2 FIX M3 FIX M4 FIX MC32/12, MC24/12—Owner’s Manual 20 Specifications 20 Specifications General specifications Frequency response 20 Hz–20 kHz +1 dB, –3 dB, +4 dB 600. (ST1 OUT, ST2 OUT, MIX OUT, MATRIX OUT) (Input Gain Control at minimum) Total harmonic distortion <0.1% @20 Hz–20 kHz, +14 dB 600. (ST1 OUT, ST2 OUT, MIX OUT, MATRIX OUT) Hum and noise (Rs=150., 20 Hz–20 kHz) –128 dB equivalent input noise –95 dB residual output noise (ST1 OUT, ST2 OUT, MIX OUT, MATRIX OUT) –83 dB residual output noise (ST1 OUT) ST master fader at nominal level. all channel fader, mix level control: minimum ST switch: OFF –78 dB residual output noise (MIX OUT) Mix master fader at nominal level. all channel fader, mix level control: minimum M1–M4 switch: OFF –64 dB (68 dB S/N) (ST1 OUT, MIX OUT) ST master/mix master fader, one channel fader and mix level control at nominal level. one channel gain control: maximum Maximum voltage gain 84 dB CH IN to ST1 OUT 84 dB CH IN to MIX OUT 58 dB ST IN to ST1 OUT 58 dB ST IN to MIX OUT Crosstalk at 1 kHz –70 dB adjacent input –70 dB input to output Gain control 44 dB variable Channel input pad 0 dB/26 dB Channel input HPF 80 Hz 12 dB/oct Input channel equalization ±15 dB Maximum HIGH 10 kHz * shelving HI-MID 400 Hz–8 kHz peaking LO-MID 80 Hz–1.6 kHz peaking LOW 100 Hz * s...
Otros modelos de este manual:Instrumentos Musicales - MC24/12 (436.89 kb)