Votos - 3, Puntuación media: 3
(
)
)
|
Resumen del manual
¦ SEND Section This section adjusts the levels and controls the flow of the signals from the six AUX buses and the two EFFECT buses. Each of these signals flows to the corresponding SEND output jack (to AUX1–AUX6, EFF1, and EFF2, respectively). 3 1 2 1 AUX Controls (AUX1 to AUX6) Each knob adjusts the level of the signal from the indicated AUX bus into the corresponding AUX SEND jack. 2 Effect Controls (EFF1, EFF2) Each knob adjusts the level of the signal from the indicated EFFECT bus into the corresponding EFFECT SEND jack and also into the corresponding internal digital effect. NOTE For each channel, you use the channel’s AUX5/6 switch (see page 11) to select between feed into the AUX5 and 6 buses or feed into the EFFECT 1 and 2 buses. If the switch is on ( ), the signal goes to the AUX5 and AUX6 SEND jacks. If the switch is off ( ), the signal goes to the EFF1 and EFF2 SEND jacks. 3 AFL (After-Fader Listen) Switches For each AUX and EFFECT bus: Use this switch to feed the corresponding AUX SEND or EFF SEND signal into the AFL bus. Feeds the corresponding AUX SEND or EFF SEND signal into the AFL bus, so that this signal can be monitored at the PHONES jack. NOTE If you set this switch on for EFF1 or EFF2, you can use the PHONES jack to monitor the signal to the corresponding internal digital effect. 14 MG32/14FX, MG24/14FX s ¦ RETURN Section This section adjusts the levels of the input from the RETURN 1 and RETURN 2 jacks (see page 20). For each RETURN, you can set independent levels for feeds into the ST bus and AUX buses 1 to 4. 32 1 32 1 1 AUX Mix Controls (1 to 4) Each knob adjusts the level of the signal from the corresponding RETURN jack into the corresponding AUX bus (AUX1 to AUX4). If you are inputting a stereo signal, the L and R signals are mixed before moving to the AUX buses. 2 ST Control Adjusts the level of the signal from the corresponding RETURN jack into the ST bus. If you are inputting a stereo signal, the L signal goes into the ST L line and the R signal goes into ST R line. If you are inputting a mono signal, the same signal is fed to both ST L and ST R. 3 PFL (Pre-Fader Listen) Switch Use this switch to feed the corresponding RETURN signal, taken from before the ST and AUX Mix controls, into the PFL bus, so that you can monitor the signal at the PHONES jack. To turn the PFL feed on, press the switch in ( ). MG32/14FX, MG24/14FX 15 Front & Rear Panels 16 MG32/14FX, MG24/14FX ¦ INTERNAL DIGITAL EFFECTS Section You use this section to control the dual internal effects processor: to select the two effect types, to set the effects on or off, and to adjust the related signal levels and flows. 1 PROGRAM Dials This dial sets the effect type for the corresponding internal digital effect. For information about the effect types, see page 24. 2 PARAMETER Controls This knob sets the parameter value for the corresponding internal digital effect. The setting applies to the currently selected effect type. The mixer saves the last value used with each effect type. When you change to a different effect type, the mixer automatically restores the value that was previously used with the newly selected effect (regardless of the current position of the Parameter Control knob). These parameter values are retained even after power-off. 3 AUX PRE Controls (1 to 4) Each knob adjusts the level of the effected sound into the corresponding AUX bus (AUX1 to AUX4). 4 TAP Button and Indicator This feature lets you set the delay time for internal EFFECT 2 by tapping on the button. The feature only works if you have set the effect type for EFFECT 2 to [16] TAP DELAY. To set the delay time, tap on the button at the appropriate interval. The mixer measures the interval between the last two taps and sets this as the delay time. Continue tapping as necessary until you get the timing right. The mixer retains the last time setting even after power goes off, and restores this setting the next time you set the effect type to TAP DELAY. The indicator next to the button flashes in sync with the delay time. 5 ON Switches This switch turns the corresponding internal digital effect on ( ) or off ( ). 6 PFL (Pre-Fader Listen) Switches Use this switch to feed the corresponding digital effect signal, taken from before the EFFECT RTN fader, into the PFL bus, so that you can monitor the signal from the PHONES jack. To turn the PFL feed on, press the switch in ( ). The signal will not feed into the PFL bus if the effect’s ON switch (5) is turned off. 7 GROUP Switches Set the switch on ( ) to feed the corresponding internal digital effect signal into the corresponding GROUP buses. The top button feeds the signal to Groups 1 and 2; the lower button feeds it to Groups 3 and 4. 8 ST Switches Set this switch on to feed the corresponding internal digital effect signal into the ST bus. 9 EFFECT RTN faders (1, 2) This fader adjusts the level of the effected sound into the ST and GROUP buses. 1 5 6 7 8 2 3 4 9 NOTE NOTE s ¦ METER/PHONES Section 5...
Otros modelos de este manual:Instrumentos Musicales - MG24/14FX (6.49 mb)