Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
Like the CUE CONTROL connector, it does not carry an audio signal, but control information as to which groups are being muted. A switch on the front panel determines whether an PM1200 functions as "Master" or "Slave" with regard to the muting function, and another switch determines the mute group buss number for the other mixing console when the master mixing console is a PM3000 or PM1800. See Page 14 (MUTE CONTROL SWITCHES) for details. The connecting plug is SRCN6A25-24 type (made by JAE). ® DC POWER INPUT CONNECTOR This connector is used to connect the locking umbilical cable to the PW1200 power supply. CAUTION: Always make sure that the power to the PW1200 is turned OFF before connecting or disconnecting this connector. 17 THE PW1200 POWER SUPPLY The PW1200 is a rack-mountable power supply designed to provide power for the PM1200 series of mixers. Since it is specifically designed for use with these mixers, DO NOT attempt to use it to supply power to any other equipment, or use any other power supply with your PM1200 mixer. (The PW1800 Power supply is also usable for PM1200 mixer.) There are two export models of the PW1200 power supply - a 120 VAC model for use in the USA and Canada, and a general model for use elsewhere in the world. The general model is switchable between 240 VAC and 220 VAC. MAKE SURE THAT YOU ARE USING THE RIGHT MODEL FOR YOUR LOCAL POWER SUPPLY! FRONT PANEL REAR PANEL FRONT AND REAR PANEL O Power switch (POWER) When this switch is depressed, AC power is supplied to the PW1200, and the correct DC voltages are supplied to the PM1200 console via the umbilical cable. The LED next to this switch indicates when the power is on. €) Operation monitor There are 4 green LED indicators to monitor the power supplied to the PM1200 mixing console (+48, +12, +17 and -17 volts). In normal operation, these LEDs should all be lit. If one or all go off, it means that there is a fault in the power being supplied to your PM1200. Contact your YAMAHA service center if this happens. © Umbilical connector This locking multi-pin female connector supplies regulated power to the PM1200 from the PW1200. To lock the connector into place, push and turn clockwise. Reverse to unlock and remove the connector. CAUTION: Always make sure that the power to the PW1200 is turned off before connecting or disconnecting this connector to or from either the console or the PW1200. O Fuses This is the primary fuse of the PW1200 power supply. If it is blown replace it only with a fuse of the same current rating and type (6 A 250 V slow-blow for USA and Canadian model, T3.15A 250 V slow-blow for the general model). Note: There are also internal fuses in the PW1200, as follows: USA and Canadian model + 17 VDC 6 A 250 V slow-blow -17 VDC 6 A 250 V slow-blow + 12 VDC 6 A 250 V slow-blow +48 VDC 2 A 250 V slow-blow General model + 17 VDC T 6.3 A 250 V slow-blow -17 VDC T 6.3 A 250 V slow-blow +12 VDC T 6.3 A 250 V slow-blow +48 VDC T 2 A 250 V slow-blow 0 Voltage selector switch (general model only) This switch selects the input voltage to the PW1200 to be either 220 V or 240 V. Make sure that it is set correctly for the voltage in your area. 0 Power cable Used to connect the PW1200 to the AC mains. 18 I PW1200 UMBILICAL CONNECTOR PIN ASSIGNMENTS Pin Function 1 E(+48 V) 2 E(+12 V) 3 E(±17 V) 4 +48 V 5 +12 V 6 +17 V 7 -17 V 8 GND 9 DETECT A 10 DETECT B CONSOLE SIDE POWER SUPPLY SIDE (MALE) (FEMALE) Umbilical Connector Pin Assignment« GENERAL SPECIFICATIONS Dimensions HEIGHT 3-1/2 inches (88 mm) (excluding feet: add 10mm for feet) DEPTH Overall, 13-3/16 inches (334.5 mm). Behind panel, 11 -3/4 inches (299.5 mm) WIDTH 18-7/8 inches (479 mm) Weight 22 lb (10 kg) Outputs + 17 VDC@1.8 A -17 VDC@1.8 A Ground (common) for 17 V + 12 VDC @1.5 A +48 VDC @ 0.3 A Ground (common) for 12 V Chassis ground -342- AC Requirements US and Canadian models: 120 V AC, 60 Hz General model: 220/240 V (switch selectable), 50/60 Hz Umbilical cable Multi-conductor cable with locking connectors to supply power to the PM1200 console. Approximately 10 ft (3 meters) long. 'Specifications and appearance subject to change without notice Unit: mm DIMENSIONS 19 334.5- MOUNTING Shelf Mounting The PW1200 can be used on any flat, level surface as long as there is adequate ventilation. Do not remove the feet as this would block airflow through the bottom panel. PW1200 Air Flow * o D VMMM pwiaoo------------ O)- — o Q Air Flow * Shell mounting Permanent-installation Rack Mounting The PW1200 can be mounted in any standard 19" electronic equipment rack. The rear panel of the rack should be left open to promote smooth airflow. Rear to the diagrams as below for ideal cooling configuration. *One vented blanking panel (1 U size) is necessary for each PW1200. Portable Rack Mounting Road cases must be durable enough to withstand rough handling and airline travel. Use a vented blanking pane...
Otros modelos de este manual:Instrumentos Musicales - PM1200-24 (2.63 mb)
Instrumentos Musicales - PM1200-32 (2.63 mb)