Votos - 2, Puntuación media: 5
(
)
)
|
Resumen del manual
This control is only active when Gain 2 is selected. 5: GAIN SELECT: Use this switch to select which Gain control is active for the Overdrive channel. With the switch in the out position, Gain 1 is selected. When the switch is depressed, Gain 2 is selected. When a footswitch is connected to the Channel / Gain Select Footswitch jack (#21), this switch is rendered inactive and the Gain Select function is controlled by the footswitch (see #21). 6: LOW: Use this control to adjust the low frequency level of the Overdrive channel. 7: HIGH: Use this control to adjust the high frequency level of the Overdrive channel. 8: LEVEL: Use this control to adjust the output level of the Overdrive channel. 9: CHANNEL SELECT: Use this switch to select either channel. With the switch in the out position, the Clean channel is selected. When the switch is depressed, the Overdrive channel is selected. The adjacent LEDs illuminate to indicate which channel is active. When a footswitch is connected to the Channel / Gain Select Footswitch jack (#21), this switch is inactive and the Channel Select function is controlled by the footswitch (see #21). CLEAN CHANNEL: A normal gain channel designed to give you crystal clear sounds to medium distortion. 10: VOL: Use this control to adjust the output level of the Clean channel. 11: LOW: Use this control to adjust the low frequency level of the Clean channel. 12: MID: Use this control to adjust the midrange frequency level of the Clean channel. 13: HIGH: Use this control to adjust the high frequency level of the Clean channel. 14: DSP LEVEL: Use this control to adjust the amount of digital effect: in its fully counter clockwise position the signal will be “dry” (without any effect). As you rotate the control clockwise the amount of effect increases. 15: DSP SELECTOR: Use this control to select one of the 16 built-in digital effects. A listing of the effects is shown on page 3 of this user’s guide. 16: INSERT: Use this jack to connect an external effects device to the amplifier. Use a stereo 1/4” male Y connector: ring = send, tip = return, sleeve = ground. (Refer to the illustration at the bottom of page 5.) 17. EXTERNAL SPEAKER: Use this jack to connect the amplifier to an external speaker. This jack is wired in series with the internal speaker, which remains active even when an external speaker is connected. 4 FXT65 Guitar Amp with DSP & Channel Tracking FXT65 Guitar Amp with DSP & Channel Tracking 1919 1414 1515 1616 1717 1818 18: POWER: Use this switch to turn the amplifier on (top of the switch depressed) and off (bottom of the switch depressed). The switch illuminates when the power is on. 19: ELECTRONIC TUNER (top panel): The electronic tuner is active whenever the amplifier is truned on, providing constant, “real time” tuning. The bottom row of LEDs indicate which note (string) is being tuned. The top row of LEDs provides directional queues to faciltate quick and precise tuning of your instrument. The indicated note (string) is properly tuned when only the center LED is illuminated. The Rear Panel (not shown): 20: FUSE: The fuse protects the amplifier from damages caused by a faulty AC power source and/or other problems. If the fuse opens, replace it ONLY with the same size and type. If the fuse continues to fail, check the AC source – if the source is okay, contact your Crate dealer for service information. 21: CHANNEL / GAIN SELECT FOOTSWITCH: Use this jack to connect the 1/4” stereo plug on the footswitch cable to the three-button footswitch (supplied). This allows you to remotely switch between the Clean and Overdrive channels and between Overdrive Gain 1 and Gain 2. When a footswitch is used, the front panel Gain and Channel Select switches (#5, #9) are rendered ineffectual. 22: DSP FOOTSWITCH: Use this jack to connect the 1/4” mono plug on the footswitch cable to the three- button footswitch (supplied). This allows you to remotely turn the DSP on and off. 23: AC LINE CORD: This grounded power cord is to be plugged into a grounded power outlet, wired to current electrical codes and compatible with the voltage, power, and frequency requirements stated on the rear panel. Do not attempt to defeat the safety ground connection. Stereo-to-mono Y-cord: Y-adapter and 2 cables: Connecting to the Insert jack: RINGTIP to Insert TIP RETURN jack RING SEND SLEEVE GROUND to Insert jack (YPP117) (1/4"-TO-1/4" MONO SHIELDED CABLES) TIP RING SLEEVE RINGTIP (STP201, 3' The Insert jack (#16) allows you to STP202, 6' STP203, 9') patch an external effects device into the amplifier prior to its power amp stage. Use Crate’s STP201, STP202, or STP203 stereo-to-mono Y-cord or an adapter such as Crate’s YPP117 and two 1/4” mono signal cables to connect the effect as to to effect effect shown to the immediate right. "OUT" "IN" jack jack External Effect to to effect effect "OUT" "IN" jack jack External Effect Suggested Settings: OUT OUT OUT IN OUT IN OUT IN IN IN Sweet 'n Clean: Just a 'Lil Nasty: Politely ...