Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
If it is connected or removed with the amp turned on, the preset could change, perhaps resulting in lost editing if done while editing a patch. The footswitch includes bank ▲ or ▼ buttons, in combination with an A/B button that selects between A and B patches, and a C override button that overrides the A/B settings and switches to C. If either the footswitch or the parameter switches are used, the other will reflect the same changes. One important difference in using the footswitch, however, is that unlike the parameter buttons, the footswitch will not scroll from user presets to factory presets or vice versa. If the amp is on a factory preset, and you want to switch to a user preset, you must first select the user preset bank via the parameter buttons. This allows the user to wrap around through the user presets (from 9.C back to 0.A), which is the most typical application of footswitch use. INTENSITY MIX MIX MIX SPEED FEED- BACK TIME WIDTH TREMOLO/ PHASER DELAY TIME TYPE ROTOR SPEED ON/OFF ON/OFF ON/OFF ON/OFF PRESET j- VOLUME R!GHT WET/DRY LEFT WET/DRY EQ/OFF V 1 / CHANNEL SELECT FX DSP О V EDIT edge -, о 9 0 10 D. П USERA CURA CHORUS/ FLANGE CHORUS/ TREMOLO/ DELAY 1 REVERB ROTARY F FLANGE PHASER SPEAKER b • b -o- • *• L At any time, the Channel Select button can be used to change the selected preamp channel from Clean to Lead, or vice versa. This can be very useful when trying patches in different modes. If you change to the next preset without storing this change, the channel selection change you made will simply be ignored. Various LED Functions: Main LED display: The main LED display indicates the preset number when in Play mode, the parameter being modified when in Edit mode, and the note being played when in Tuner mode. As previously indicated, the center decimal point in the main LED display indicates whether the bank is set to the user or factory bank of presets. The right decimal point in the main LED display will illuminate, indicating that the DSP (Digital Signal Processor) is close to clipping. For the quietest operation, set the preamp volumes and effect preset levels so that this indicator flickers occasionally, (i.e. set the preamp volume controls so the light flickers and use the preset volume control to set the “volume” to taste). However, for the cleanest operation, avoid settings where this light stays on constantly. Channel LEDs: The channel that is active will have the LED illuminated that is within its control area. The LEDs are different colors — green for Clean and red for Lead — to allow for easier distinction when viewing from a distance. 10 Effects LED Matrix: When in Edit mode, the Effects LED matrix on the far right of the amplifier is used to indicate which effect and which parameter is being edited. If the tuner is activated, the bottom row of LEDs indicates how sharp or how flat the note is. When in Play mode, the LED matrix indicates which effects are active. This way it is easier to identify the preset at a glance. x I / CHANNEL SELECT / \ 0 10 USERA CLIP A STORE PLAY/ /-” 0 ' TUNER- DEPTH INTENSITY RATE SPEED CHORUS/ FLANGE TREMOLO/ PHASER ON/OFF ON/OFF CHORUS/ FLANGE ¡131 TREMOLO/ PHASER b SPEED TIME WIDTH DELAY I REVERB • -0- • PRESET g VOLUME" RIGHT WET/DRY ROTOR LEFT SPEED WET/DRY ON/OFF EQ/OFF EQ o* This particular display indicates the amp is set to User patch l.C, and the following effects are active: Chorus/ Flange, Tremolo/Phaser, Rotary Speaker, and EQ. Footswitch LEDs: The LEDs on the footswitch show which preset is selected: A, B, or C. This works as follows: If the C LED is off, the setting will be A or B — depending on which is lit. To change between A and B, simply press the A/B switch. To switch to C, press the C override button, which overides the setting of the A/B switch — when the C LED is lit, the preset is on C — regardless of the A/B setting. To return to A or B, first make sure the appropriate one is lit, then press C to return to A or B. This system is great for toggling between two presets, by simply hitting the same button over and over, when jumping in and out of solos, etc. PRESET OVERRIDE A/B Ш /ЧЕШЕК , REMOTE SWITCH This footswitch displays that the amp is set to preset C, and if the C OVERRIDE button were to be pressed, the amp would switch to preset A. 11 Tuner Mode: If the Play/Tuner button is pressed while in Play mode, the TransFex 208s will switch to Tuner mode. The tuner may also be accessed from the footswitch by pressing the bank ▲ or ▼ buttons simultaneously. To return to the previous preset press the A or T buttons on the amp or any of the four footswitch buttons. The Channel Select button can be used to select between the Clean channel or muted output. This selection will remain in memory until altered. The tuner is a full chromatic one, with LEDs indicating how flat or how sharp the note is. When the note is in tune, both of the center LEDs will illuminate. DE...
Otros modelos de este manual:Instrumentos Musicales - TransFex 208s (6.08 mb)