Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
PARA DISMINUOIR EL RIESGO DE CORRIENTAZO. NO ABRA LA CUBIERTA. NO HAY PIEZAS ADENTRO QUE EL USARIO PUEDO REPARAR DEJE TODO MANTENIMIENTO A LOS TECHNICOS CALIFICADOS. ATTENTION RISQUE D'ELECTROCUTION NE PAS OUVRIR ATTENTION: PROTEGEZ CET APPAREIL DE LA PLUIE ET DE L'HUMIDITE AFIN D'EVITER TOUT RISQUE D'INCENDIE OU D'ELECTROCUTION. POUR REDUIRE D'ELECTROCUTION NE PAS ENLEVER LE COUVERCLE. AUCUNE PIECE INTERNE N'EST REPRABLE PAR L'UTILISATEUR. POUR TOUTE REPARATION, S'ADRESSER A UN TECHNICIEN QUALIFIE. INPUT 1 LEVEL1 INPUT 2 LEVEL 2 EXT. SPEAKER HEAD PHONES POWER AMP ATTENUATORLO LO MID HI MID HI EQ LIMITER CD INPUT KXB15 Keyboard Amplifier KXB15 Keyboard Amplifier 1 2 34 5678911111213 1. INPUT 1: Use this 1/4” jack to connect your keyboard or other line level signal to the amplifier by means of a shielded instrument cable. The signal level at this jack is controlled by the Level 1 knob (#3). 2. INPUT 2: Use this 1/4” jack to connect your keyboard or other line level signal to the amplifier by means of a shielded instrument cable. The signal level at this jack is controlled by the Level 2 knob (#4). 3. LEVEL 1: Use this control to adjust the level of the signal connected to the Input 1 jack (#1). 4. LEVEL 2: Use this control to adjust the level of the signal connected to the Input 2 jack (#2). 5. LOW: Use this control to adjust the bass response of the amplifier. Rotating the control counterclockwise reduces the low frequency output. Rotating the control clockwise increases the low frequency output. It may be necessary to reduce the Low frequency output at higher volume levels. 6. LO MID: Use this control to adjust the “thickness” or “fatness” of the amplifier. Rotating the control counterclockwise reduces the lower midrange frequency output. Rotating the control clockwise increases the lower midrange frequency output. 7. HI MID: Use this control to adjust the clarity and definition of the amplifier. Rotating the control counterclockwise reduces the upper midrange frequency output. Rotating the control clockwise increases the upper midrange frequency output. 8. HIGH: Use this control to adjust the high frequency response of the amplifier. Rotating the control counterclockwise reduces the high frequency output. Rotating the control clockwise increases the high frequency output. 9. CD INPUT: Use these RCA jacks to connect the output from a CD player or tape deck to the amplifier. The signal at these jacks is combined into a mono signal which is sent to the internal power amp circuit. Use the CD or tape player’s output level control to adjust the signal for the proper mix with your instrument. 10. (EXTERNAL SPEAKER): Use this jack to connect the amplifier to an external speaker. The internal speaker is disconnected when this jack is used. The impedance of the external speaker must be 4 ohms or greater. WARNING: Do not attempt to use headphones in the Speaker jack! Permanent hearing damage could result! 11. (HEADPHONES): Use this jack to connect headphones to the amplifier. The internal speaker is disconnected when this jack is used. A line level signal can also be obtained from this jack for recording, etc. CAUTION: To avoid possible damage to your hearing, do not use headphones for extended periods of time at extremely loud levels. 12. ON: This LED illuminates when the amplifier is turned on. 13. POWER: Use this switch to turn the amplifier on (top of the switch depressed) and off (bottom of the switch depressed). 14. POWER CORD (rear panel, not shown): The grounded power cord should only be plugged into a grounded power outlet that meets all applicable electrical codes and is compatible with the voltage, power, and frequency requiremnts stated on the rear panel. Do not attempt to defeat the safety ground connection. KXB15 Keyboard Amplifier KXB15 TECHNICAL SPECIFICATIONS: Maximum Input Signal Level Accepted 15 volts peak to peak load – 120 VAC line Low Control 15dB Range @ 50Hz Low Mid Control 12dB Range @ 250Hz High Mid Control 13dB Range @ 1kHz High Control 27dB Range @ 10kHz Input Power Requirements 120 VAC, 60Hz, 30VA 100/110 VAC, 50/60Hz, 30VA 230 VAC, 50/60Hz, 30VA Speaker Size and Rating Crate Custom Design 8”, 15 watts Cabinet Size and Weight 14” H x 15” W x 12-1/2” D, 19 lbs. Declaration of Conformity Manufacturer’s Name: SLM Electronics Corporate Headquarters: 1901 Congressional Drive, St. Louis, Missouri 63146 Primary Production Facility: 700 Hwy 202 W, Yellville, Arkansas, 72687 Product Type: Audio Amplifier Products meet the regulations for compliance marking under: ETL standards UL6500, UL60065, or UL813 CSA standards E60065 or C22.2 No.1-M90 CE safety standard EN60065 CE EMC standards EN55103 or EN55013 and EN61000 C-tick designation Level 2, ABN #56748810738, ARBN# N222 KETI standard K60065 (limited model approval) Compliance Support Contact: SLM Electronics, Attn: R&D Compliance Engineer 1901 Congressional Drive, St Louis, Missouri, 63146 • Tel.: 314-569-0141, Fax: 314-569-0175 crateamps.c...