Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
L DEPTH , E60KL ® ® ® o a FOOT UNS UNË - _ SWITCH OUT IN POWER J i i i i ^ * i { j { I Ï I It t t I I i j i t t! t 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 FRONT PANEL—INPUT SECTION 1. OdB INPUT JACK: This input accepts a standard 1/4" phone plug and is suitable for any low to line level signal source such as an electric guitar. 2. - 6 dB INPUT JACK: This input also accepts a standard 1 /4"jack but is padded 6 dB for hotter inputs such as tape decks or guitars with hot pickups. If both jacks are used, this input is not padded and will be equal to the 0 dB input jack. CHANNEL A CONTROLS 3. GAIN CONTROL: This control sets the amount of gain for Channel A and is used to vary the amount of distortion. Minimal distortion is achieved with this control rotated counterclockwise. A fully clockwise setting creates maximum distortion. 4. LEVEL CONTROL: The overall volume of Channel A is controlled with this knob and should be used in conjunction with the GAIN CONTROL|3). 5. SHAPE CONTROL: This is the overall tone control for Channel A. When turned to the left, a setting with heavy emphasis on mid range is achieved. When rotated to the right, the amp creates a "fat" sound with extra boost on lows and highs. 6. CHANNEL A INDICATOR: The amplifier is in Channel A mode with this LED lit. 7. CHANNEL SELECT SWITCH: This switch is used to select between Channel A and Channel B. When using the optional footswitch, this switch should be in the Channel A position. 8. CHANNEL B INDICATOR: The amplifier is in Channel B mode with this LED lit. CHANNEL B CONTROLS 9. VOLUME CONTROL: This control sets the overall listening level of Channel B, This control is independent of any setting made in Channel A. 10. HIGH CONTROL (Treble): This knob will affect the upper harmonic range of the guitar. Boosting it sharpens or adds crispeness to the sound. For additional effect, use this control in conjunction with the Bright switch (13). 11. MID CONTROL (Mid): The tonal qualities of the midrange are very important to a good guitar sound. This knob can "thin-out" the sound when turned down, or "fatten-up" the tone when larger amounts are used. 12. LOW CONTROL (Bass): The desired amount of "Bottom" or "Warmth" may be increased or decreased with 13. BRIGHT SWITCH: This switch affects the brilliance of the guitar's sound by adding additional "bite" or sharpness. This switch affects both Channel A and B. 14. DEPTH CONTROL (REVERB): This control allows the player to alter the apparent acoustical qualities of a room. The sound can be altered from very "Flat" or "Dry" when the control is turned off, to that of a concert hall when used in larger amounts. 15. FOOTSWITCH JACK: This jack is to be used with the Channel Selector/Reverb footswitch. 16. LINE OUT JACK: This jack is used to link the G-60XL to additional amplifiers or to connect the amp to a tape recorder. Simply run a cable from the output of this jack to the input of another amplifier or tape deck. External speakers cannot be hooked up to this jack. 17. LINE IN JACK: This jack is used as a direct input to the cower amo. It can OUT jack for an effect loop. POWER 18. ON/OFF LED INDICATOR: The amplifier is on when the LED is lit. 19. ON/OFF SWITCH: This is a two position switch, the down position will turn the unit on, while the up position off. REAR PANEL POWER CORD: Your G60XL is equipped with a heavy-duty grounded three-wire power cord. Be sure this cord is properly plugged into a safely wired grounded 120 volt, 60 hz AC power outlet before use. (If your G60XL was purchased outside the United States, refer to the rear panel for power ratings). For your safety, never attempt to defeat the ground connection on this cord. G60XL TECHNICAL SPECIFICATIONS Output Power Rating 60 watts RMS @ 5% THD 4 ohm load —120 VAC line Speaker Size and Rating: G60XL: Custom Design 12 "with 1-1/2 "voicecoil Power Handling 60 watts RMS G60XLS: Celestion G12M-70 G60XLF: Fane Medusa Low Control 15 db range @80 Hz Mid Control 15 db range @ 500 Hz High Control 20 db range @ 5 KHz Bright Switch 5 db boost @6 KHz Input Impedance 220K ohms/"0 db" input 44K ohms/" - 6 db" input Maximum Input Signal Level Accepted 4 volts, peak to peak/"0 db” input 8 volts, peak to peak/" - 6 db" input Total System Gain Channel A: 105db(S 1 KHz (Shape @ 0, Bright Switch off) Channel B: 62 db@ 1 KHz (Controls («' 10, Bright Switch off) Signal to Noise Ratio Channel A: 40 db—with Gain, Level @ 10, Shape @ 0 Channel B: 68 db—with all controls @ 10, Bright Switch off Input Power Requirements 120 VAC, 60 Hz, 200 watts max Fuse Rating and Type 2 amp, 250V internal Cabinet Size and Weights 17-1/2’ H x 18-1/4"Wx 9-3/4" D 34 lbs. Specifications subject to change without notice. CAUTION: To reduce the risk of electric shock, do not remove chassis. No user serviceable parts inside. Refer servicing to qualified service personnel. CAUTION: This equipment is capable of producing sound pressure level...