Votos - 0, Puntuación media: 0
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
* Make sure the tailpiece side of the bridge stands vertically in relation to the body. [Direction the pegs should be turned and Insert the string’s end the direction the strings should be wound] into this hole [Looking from the front] Correct 1st string (A) 2nd string (D) 4th string (C) 3rd string (G) 3rd string 4th string 2nd string 1st string Three to five wraps Tailpiece Body Bridge seat Bad Bad Vertical 4 Use a piano, tuning fork, tuner, etc., and adjust the pitch of each string using the tuning pegs. * Refer to the “Tuning” section (page 7). • When the instrument is not going to be used for an extended period of time, loosen the strings until the pitch drops a whole tone. • Before using the instrument, make sure that the bridge is positioned vertically. Damage to the bridge and poor sound quality may result if the bridge is not properly positioned. Power Supply The Silent Electric Cello can be operated with either battery or AC power. Always turn the power switch (OFF/ON/REV.ON) on the rear panel OFF before making AC power connections or replacing batteries. ¦ Using Batteries 1 Open the battery compartment situated on the back of the Silent Electric Cello. 2 Insert the two batteries supplied (SUM-3 (AA) size). Take careful note of the polarity markings as shown in the illustration above, and insert the batteries. 3 Replace the battery compartment cover. Bij dit produkt zijn batterijen geleverd. Wanneer deze leeg zijn, moet u ze niet weggooien maar inleveren als KCA. SUM-3 (AA) size battery x2 Battery compartment cover Slide the POWER switch to the ON position, the lamp will light green. Slide the switch to the REV. ON position, the lamp will light red. When battery power is low, the lamp’s color changes to orange, the sound becomes distorted, the Reverb does not properly function, and noise becomes audible. When one of these symptoms appears, take note of the following cautions and replace the batteries. • Always follow the +/– signs when inserting the batteries. Improper insertion may result in fire. • Always replace worn batteries with a complete set of new batteries. Never mix new and old batteries. Do not mix different types of batteries (alkaline and manganese, or batteries from different manufacturers, or different types by the same manufacturer). Doing so may result in fire. • To prevent possible damage to the unit due to battery leakage and unnecessary power drain, remove the batteries from the unit when it is not going to be used for an extended period of time. ¦ Supplying AC Power AC adaptor is optional, please purchase the optional power adaptor PA-3B or PA-3C. 1 Plug the adaptor’s DC output cable into the Silent Electric Cello’s DC IN 9-12V jack located on the back of the instrument, making sure the plug is firmly inserted into the jack. 2 Plug the AC adaptor into a convenient wall AC power socket. • Battery power is automatically disconnected when the AC adaptor is connected. • When the AC adaptor is used, the batteries may leak. To prevent leakage we recommend that you remove the batteries from the instrument. When the AC adapter is used. • When using an AC adaptor, make sure you use only the appointed compatible adaptor. The use of an incompatible adaptor may result in damage to the instrument or cause fire, etc. Please use with caution. Using the Controls 1 Slide the POWER switch, located on the rear of the instrument, to its ON position. The lamp will light green. 2 Connect a pair of stereo headphones to the PHONES jack on the rear of the instrument. Make sure that the L&R sides of the headphones are positioned on the correct ears. 3 Rotate the VOLUME dial to the desired playing level. Lights green • When using the headphones, do not operate at high volume levels or long periods of time. Doing so can lead to irreparable damage to your hearing. Lights red The Reverb The Silent Electric Cello incorporates Yamaha’s DSP reverb technology. Play while trying out the three types of reverb. 1 Slide the POWER switch to the REV. ON position, the lamp will light red, and reverb will be applied to the Silent Electric Cello’s sound. 2 Slide the REVERB switch to select one of the three reverb modes. • RM (ROOM) mode ......... this reverb simulates the natural reverberation found in a room. • HL1 (HALL 1) mode ...... this reverb simulates the natural reverberation found in a hall. • HL2 (HALL 2) mode ...... the same reverb simulation as HL1 but with a longer decay time. 16 Connecting External Devices Silent Electric Cello Stereo Headphones SUM-3 (AA) size * Supplied headphones or any other type battery x2 or Power Adaptor (Option : PA-3B or PA-3C) Electric Outlet • Using the cord hook Wrap the Power Adaptor’s cord around the cord hook (prevents cord from being unplugged). Power Adaptor Cord Cord Hook DC-IN 9-12V DC-IN 9-12V From the LINE OUT jack, etc. CD Player MDP5 Mobile Data Player Cassette Player Electronic Metronome (with audio output jack) To the LINE IN jack, etc. Powered Speaker (AS60-112T,...