Votos - 0, Puntuación media: 0
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
Samples assigned to any track of the current pattern or song can be edited. Samples have four Play Modes which determine how they are played back. The play mode is specified in the Sample Edit Sample Parameter page (Page 242). The four play modes are listed Sample Edit Procedure 1. In the PATTERN or SONG Play mode, stop playback of the sequence and then select the track to which the sample voice you want to edit is assigned (Page 73, 183). 2. Press [SAMPLE EDIT] to go to the Trim page. 3. If the selected sample voice is a Sample Kit Voice, press the [KEYBOARD] button so that its indicator lights, and then press the key on the keyboard corresponding to the sample 5 below: you want to edit. The Sampling FORWARD .........The sample plays from the start point to the end point. REVERSE ...........The sample plays in reverse from the end point to the start point. LOOP ..................The sample loops repeatedly from the start point to the end point. ATK+LOOP ........After playing from the start point to the end point, the sample loops between the loop start point and the end point. 4. Use [Knob 1] ~ [Knob 4] to change the settings as required. 5. Press [SAMPLE EDIT] to go to the Sample Parameter page. 6. Use [Knob 1] ~ [Knob 4] to change the settings as required. 7. Press [EXIT] to go back to the Trim page, and then again to return to the original display. Display Parameters [1] Trim Page REVERSE LOOP ATK+LOOP START(ATCK) START(LOOP) START END FORWARD [SAMPLE EDIT] 4 5 7 8 3 6 1 2 9 [Knob 1] [Knob 2] [Knob 3] [Knob 4] [F1] [F4][F2] RS7000 241 3.3. 1 ZOOM IN/OUT ......................................................[Knob 1] [Settings] IN, OUT Rotate counter-clockwise to zoom in. Rotate clockwise to zoom out. Above a certain zoom-in level, the waveforms near the start and end points will be shown on the left and right halves of the display. 2 ZOOM...............................................................................[F1] When the ZOOM IN/OUT parameters is set to IN or OUT, each press on this button zooms the waveform display either in or out, respectively. 3 START Point, START (ATCK) Point, START (LOOP) point .........................................................................[Knob 2] [Settings] 0 ~ END Point Sets the sample start and/or loop start points. When PLAY MODE = FORWARD, REVERSE, or LOOP Sets the START point. When PLAY MODE = ATK+LOOP [F2] switches between START(ATCK) and START(LOOP). Sets the initial sample start point when START(ATCK) selected. Sets the loop START point when START(LOOP) selected. NOTE The PLAY MODE parameter is set in the Sample Parameter page (Page 242). 4 END Point .............................................................[Knob 3] [Settings] START Point ~ End of sample Specifies end point of the sample. 5 STEP.........................................................................[Knob 4] [Settings] .1, .10, .100, .1000, .10000, .100000 Sets the “magnification factor” to be used when [Knob 2] and [Knob 3] are used to specify the START and END points. Higher settings allow higher value changes. 6 START ATCK / LOOP ...............................................[F2] [Settings] START(ATCK), START(LOOP) START(ATCK)...... Sets the sample start point. START(LOOP)...... Sets the loop start point. When the PLAY MODE is set to ATK+LOOP this button switches the parameter to be adjusted by [Knob 2]. The button alternately selects the START(ATCK) and START (LOOP) parameters. START(ATCK) .......Sets the initial playback start point for the sample. START(LOOP) ........ Sets the point at which the sample loop begins. 7 AUDITION...................................................................... [F4] The sample will loop between the specified START and END points while this button is held. This lets you hear precisely how the settings are affecting the sample. 8 VOICE (Sample Voice Number) [Settings] Sample Voice Number ............ 001 ~ 128 are local sample voices; C001 ~ C128 are common sample voices. Sample Name ...... Display only. Key Number (when a Sample Kit Voice is selected) ............ C-2 ~ G8 Displays the number and name of the sample voice assigned to the currently selected track. When a Sample Kit Voice is assigned to the current track, the key number can be changed to change the sample to be edited. Refer to “Sample Edit Procedure”, step 3, on page 241 for information on changing the track and key number. 9 Sample Information [Settings] All are display only. Sampling Frequency .... kHz Mono/Stereo ................ MONO, STEREO Sample Type ................ KIT (Sample Kit Voice), PITCHED (Pitched Voice) Shows the sampling frequency, mono/stereo status, and sample type (KIT, PITCHED) of the selected sample. [2] Sample Parameters [SAMPLE EDIT] . 2 Sample Voice = PITCHED VOICE 6 4 5 7 1 [Knob 1] [SHIFT]+[F1] [Knob 4] [F4] 242 RS7000 3.3. Sample Voice = SAMPLE KIT VOICE 4 PLAY MODE......................................................... [Knob 4] [Settings] FORWARD...