Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
For lamp installation in 230V environments please read Lamp (In-Series) Wiring..in the Appendix section of this manual. Do not touch the envelope (glass area) of the bulb with bare hands. If this happens, clean the lamp with alcohol and wipe it with a lint free cloth before installation. LAMP INSTALLATION 1) Remove the three (S1) screws that surround the fixture.s top cover. 2) If replacing the lamp, remove old lamp first. 3) Reach in and using a cloth or napkin hold the bulb and pull out of the lamp socket located inside the reflector. 4) Replace with a new lamp. 5) Replace fixture cover, align the screw holes and fasten the screws. 6) No lamp alignment is necessary for this fixture since the lamp is already optimized inside the reflector. Mounting ORIENTATION This fixture may be mounted in any position provided there is adequate room for ventilation. RIGGING Hanging Clamp It is important never to obstruct the fan or vents pathway. Mount the fixture using, a suitable .C.or .O.type clamp. Adjust the angle of the fixture by loosening both knobs and tilting the fixture. After finding the desired position, retighten both knobs. . When selecting installation location, take into consideration lamp replacement access and routine maintenance. . Safety cables should always be used. . Never mount in places where the fixture will be exposed to rain, high humidity, extreme temperature changes or restricted ventilation. Note! Clamps sold separately! Lamp exposed (3) thumb screws surround and fastens the top cover to the fixture, the remaining (2) are not seen in this picture S1 Lamp inside the reflector CH-258 User Manual 5 2006-05-04/23:59 OPERATING INSTRUCTIONS$ The Cyborg is a high output sound activated effect light. It produces an old favored mushroom like light movement but uses a new high polished aluminum reflector for a unique and brilliant beam pattern. The Cyborg is equipped with an internal microphone and a sound sensitivity knob. The user can adjust the sensitivity of the microphone for obtaining optimum sound activated response of its movement. Whether used in a mobile or permanent environment, you may find it useful to control this effect by means of a relay system for remote switching or to go with DMX control, use the latest in DMX compatible (Dimmer Relay Pack), all available from CHAUVET. A relay system will allow you to remotely trigger the Cyborg and any other non-dimmable effect light from a switch panel. Make sure to use a cable of at least 25 feet to provide ample distance between the control panel and the switch pack for most mobile lighting applications. If you would prefer to control it directly from your DMX lighting console then we suggest a DMX compatible (relay switch-pack). These devices are an extremely affordable solution to operating non- DMX lighting effects remotely. Duty Cycle It is necessary to cycle On and Off this fixture every 15 minutes due to the high temperature created while in use. For every 15 minute period that the fixture is used, allow 15 minutes in the Off position to cool down. Please do not exceed 15 minutes of On operation per cycle. To learn more about these and other CHAUVET products visit us at CH-258 User Manual 6 2006-05-04/23:59 PPENDIX A General Maintenance To maintain optimum performance and minimize wear fixtures should be cleaned frequently. Usage and environment are contributing factors in determining frequency. As a general rule, fixtures should be cleaned at least twice a month. Dust build up reduces light output performance and can cause overheating. This can lead to reduced lamp life and increased mechanical wear. Be sure to power off fixture before conducting maintenance. Unplug fixture from power. Use a vacuum or air compressor and a soft brush to remove dust collected on external vents and internal components. Clean all glass when the fixture is cold with a mild solution of glass cleaner or Isopropyl Alcohol and a soft lint free cotton cloth or lens tissue. Apply solution to the cloth or tissue and drag dirt and grime to the outside of the lens. Gently polish optical surfaces until they are free of haze and lint. Do not to touch the lamp glass when cleaning fixture. Oil and dirt can cause damage and premature aging of the lamp. In the event that the lamp is touched or becomes dirty, clean the lamps with an alcohol wipe. The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit.s optics. Clean with soft cloth using normal glass cleaning fluid. -Always dry the parts carefully. -Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days. Returns Procedure Returned merchandise must be sent prepaid and in the original packing, call tags will not b...