To return to the previous option or menu without changing the value, press the button. Menu Map M MENU OPTION The starting addrbu Adobe Systems ttons. Stand Alone – Automatic: The built in programs will trigger automatically to a pre- programmed speed time. Adobe Systems Sound Active – Master Unit: Sets the fixture to Master status for Master-Slave operation and the built in programs will be triggered by the sound. No data link is Adobe Systems required; all fixtures can be set to this mode for Stand-alone operation. Slave Unit: Sets the fixture to run in sync with the Master. You must set the first fixture in the data link to “Master” otherwise nothing will happen. Adobe Systems TO SET THE PAN TO INV 1) Press until is displayed. Use the Adobe Systems Adobe Systems Adobe Systems Press until isplayed. 2) Use the and buttons to scroll through the two o Adobe Systems inverting; is Adobe Systems Adobe Systems Press and button until button. The fixture will now load all factory default settings. Adobe Systems e Mode (Sound-Active, Aue): 1) Press until 2) Use the and buttons to scroll through until the desired mode is displayed and Adobe Systems , Adobe Systems Adobe Systems Adobe Systems Adobe Systems when sound-active mode is se Adobe Systems Adobe Systems nit will auto change in Auto Mode. Master/Slave Mode (Master Sound, Master Auto): This mode will allow you to link up to 32 units together without a controller. 1) Use standard DMX cables to daisy chain your units together via the DMX connector on the rear of the units. For longer cable runs we suggest a terminator at the last fixture. For more information about terminators, see page 8. 2) Choose a unit to function as the master. Press until Adobe Systems , Adobe Systems , or Adobe Systems is displayed on the master unit. 3) Use the and buttons to scroll through until the desired mode is displayed and press the button. Adobe Systems is auto mode; Adobe Systems is sound-active. 4) Adobe Systems will be displayed when auto mode is selected; Adobe Systems will be displayed when sound-active mode is selected. 4) Press until Adobe Systems , Adobe Systems , or Adobe Systems is displayed on the slave units. Use the and buttons to scroll through until Adobe Systems is displayed and press the button. 5) Adobe Systems will be displayed when slave mode is selected. DMX Mode This mode allows the unit to be controlled by any universal DMX controller. If you are unfamiliar with DMX, please read the DMX Primer on page 15. 1) Press until Adobe Systems is displayed. 2) Use the and buttons to select the desired address and press the button. DMX Channel Values CHANNEL VALUE FUNCTION 1 000 .. 255 Pan: 128 = halfway point 2 000 .. 255 Pan Fine 3 000 .. 255 Tilt: 128 = halfway point 4 000 .. 255 Tilt Fine 5 000 .. 255 Vector Speed: (Normal > Slow) 6 000 .. 007 008 .. 023 024 .. 238 239 .. 255 Lamp On/Off & Strobe Blackout Open Strobe: Slow > Fast Open 7 000 .. 255 Dimmer (100 – 0%) 8 000 .. 250 251 .. 255 Reset No Function Reset (after 10 seconds) General Troubleshooting Symptom Solution(s) Applies to Lights Foggers & Snow Controllers Dimmers& Chaser Auto shut off Check fan thermal switch reset .. Beam is very dim or not bright Clean optical system or replace lamp Check 220/110v switch for proper setting .. Breaker/Fuse keeps blowing Check total load placed on device .. Chase is too slow Check users manual for speed adjustment .. .. .. Device has no power Check for power on Mains. Check device’s fuse. (internal and/or external) .. .. .. Fixture is not responding Check DMX Dip switch settings for correct addressing Check DMX cables Check polarity switch settings .. Fixture is on but there is no movement to the audio Make sure you have the correct audio mode on the control switches. If audio provided via .” jack, make sure a live audio signal exists Adjust sound sensitivity knob .. .. .. Lamps cuts off sporadically Possible bad lamp or fixture is overheating. Lamp may be at end of its life. .. Light will not come on after power failure Some discharge lamps require a cooling off period before the electronics in the fixture can kick start it again, wait 5 to 10 minutes before powering up .. Loss of signal Use only DMX cables Install terminator Note: Keep DMX cables separated from power cables or black lights. .. .. .. .. Moves slow Check 220/110v switch for proper setting .. No flash Re-install bulb, may have shifted in shipping .. No laser output Bounce mirror motor may have shifted during shipping, readjust .. No light output Check slip ring & brushes for contact Install bulb Call service technician .. Relay will not work Check reset switch Check cable conn...
)
Iniciar sesión: