Iniciar sesión:
Votos - 2, Puntuación media: 3 ( )

Manual de usuario Alvarez, modelo OC-20G

Fabricar: Alvarez
Tamaño del archivo: 859.59 kb
Nombre del archivo: OC-20G_OM.pdf
Idioma del manual:en
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


18; p. 21). These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, Owner’s manual should be read in its entirety. The manual should be saved and kept on hand as a convenient reference. Copyright © 2001 BOSS CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of BOSS CORPORATION. Main Features New kind of effect for use with GK pickups and GK-Ready guitars. Six independent selectable octave processors: on for each string. Built-in distortion for ultra-heavy sound. Send and return for direct guitar signal. The controls and pedals provide simple and intuitive operation. Can run on battery power (six AA type). 2 Installing Batteries Insert the included batteries as shown in figure, being careful to orient the batteries correctly. fig.02 • When turning the unit upside-down, get a bunch of newspapers or magazines, and place them under the four corners or at both ends to prevent damage to controls. Also, you should try to orient the unit so no controls get damaged. • When turning the unit upside-down, handle with care to avoid dropping it, or allowing it to fall or tip over. • Make sure the “+” and “-” ends of the batteries are oriented correctly. • When the batteries run down, the POWER indicator gets dim. If this happens, replace with new batteries. • When replacing the batteries, use six AA type. • Do not mix fresh batteries with used ones, or mix batteries of different types. Doing so can result in fluid leakage. • Battery life can vary depending on battery type. Continuous usage time under battery power is about 6 hours with alkaline batteries and about 2 hours with carbon batteries. (This may vary according to usage conditions.) Making the Connections About the GK-2A To use the OC-20G with a guitar equipped with the GK-2A (or other GK- compatible guitar), you will need an optional GK cable. Refer to the GK-2A Owner’s Manual for instructions on installing the GK-2A. S1/S2 Switch The GK-2A’s S1/S2 switches correspond to this unit’s MASTER On/Off pedal and Distortion On/Off pedal, respectively. Selection Switch Set to the “MIX” position. Note that this unit processes tones using the instrument’s divided pickup signal (signal output when SYNTH is selected). No sound is produced when the following settings are combined. GK-2A This unit’s settings SYNTH MASTER: OFF GUITAR MASTER: ON + NORMAL PU MIX: OFF (rear panel) SYNTH VOL Knob Controls the volume when MASTER ON is selected. Connecting Guitar Amp AC Adaptor PSA-series (sold separately) Guitar with GK-2A or other GK-compatible guitar Making the Connections • To get the best performance from the instrument, set your amp to “Clean” (no distortion). • When connecting the instrument to a guitar amp, make the necessary adjustments to get the most suitable tone. When recording direct, use this with a COSM amp (GT-3, GP-20 etc.). • When connecting a GK cable, insert the cable completely until the connector is securely locked. When disconnecting, press the connector’s lock while you detach the cable. * Always turn the amp volume down completely before connecting and disconnecting cords. * To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections. * If there are batteries in the unit while an AC adaptor is being used, normal operation will continue should the line voltage be interrupted (power blackout or power cord disconnection). Turning On the Power Be sure to observe the following order when connecting devices and switching on the power to your equipment. By turning on devices in the wrong order, you risk causing malfunction and/ or damage to speakers and other devices. Connect the GK-2A . (Connect the AC Adaptor) . Connect the Amp . Turn On Amp Power * When the unit is running on battery power, the power comes on when you insert the connector plug into the OUTPUT jack. * Always make sure to have the volume level turned down before switching on power. Even with the volume all the way down, you may still hear some sound when the power is switched on, but this is normal, and does not indicate a malfunction. * When operating on battery power only, the unit’s indicator will become dim when battery power gets too low. Replace the battery as soon as possible. 5 Operating Instructions Using the Pedals fig.04 “MASTER: ON” and “DISTORTION: OFF” are selected when the power is turned on. Master is toggled on and off by stepping on the MASTER On/Off pedal. When switched on, the GK effect sound is output. When off, the output from the divided pickup is muted, and the sounds from the normal pickup (or the sounds input to GUITAR RETURN) are output without change. Distortion is toggled on and off by stepping on the Distortion On/Off pedal. When Master is ...

Otros modelos de este manual:
Instrumentos Musicales - OC-20G (859.59 kb)
Instrumentos Musicales - OC-20G (859.59 kb)

Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría