Votos - 2, Puntuación media: 5
(
)
)
|
Resumen del manual
21. STATION CALL: These buttons are used to preset the desired broadcasting stations. 22. TUNER SEEK (UP/DOWN): Up: Performs tuning in ascending frequency order. Down: Performs turning in descending frequency order. 23. POWER ON: Press this button to turn the Cinema 11a ON. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 AUTO SETUP HDAM HDFM FM AM FM MODE TEXT DISPLAY POWER OFF POWER ON TUNER SEEK TUNER SCAN MEMORY BRIGHT EQ ENTER SETUP LATE INPUT SELECTOR 7.1 IN HDMI 1 HDMI 2 INPUT SEEK MUTE VOLUME PLIIx SUR. MODE NEO:96/24 CES 7.1 ZONE 2 REMOTE CONTROL This section explains how to use the Zone 2 remote control in a remote room in your house. (2nd Zone room) 1. ZONE 2 POWER OFF: Press this button to power OFF Zone 2. 2. ZONE 2 PRESET: These buttons are used to preset desired broadcasting stations. 3. ZONE 2 VOLUME: Press this button to adjust the Zone 2 volume up and down from -90dB to +15dB. 4. ZONE 2 INPUT SELECTOR: Use these buttons to select the Zone 2 desired source for your Cinema 11a. 5. ZONE 2 MUTE: Press this button to mute the Zone 2 volume. 6. BAND (FM): Press this button to select the FM frequency band in Zone 2. 7. BAND (HDFM): Press this button to select the HDFM frequency band in Zone 2. 8. BAND (AM): Press this button to select the AM frequency band in Zone 2. 9. POWER ON: Press this button to power ON Zone 2. 10. BAND (HDAM): Press this button to select the HDAM frequency band reception in Zone 2. 1 2 3 4 5 6 6 7 AM 8 FM HD AM HD FM 7.1 IN MUTE 1 2 3 4 5 6 7 8 ZONE 2 REMOTE _ O I INPUT VOLUME + POWER ON POWER OFF PRESET PRESET HDMI1 HDMI 2 10 LOCATION To assure proper operation and to avoid the potential for safety hazards, place the unit on a firm and level surface capable of supporting its weight. When placing the unit on a shelf, be certain that the shelf and any mounting hardware can support the weight of the unit and any additional items in the equipment rack, or on the shelf. When positioning the Cinema 11a, make certain that it has adequate ventilation on all sides, as well as on the top and bottom. In particular, it is a good idea to provide at least two or three inches of room above the unit for air circulation. DO NOT place CDs, DVDs, videotapes, owner's manuals, or other paper on top of, or beneath, the unit, or in-between multiple amplifiers in a stack. This will block airflow, causing heat buildup, and may create a possible fire hazard. If the unit is to be enclosed in a cabinet or rack, make certain there is adequate air circulation. Sufficient ventilation should be provided so that hot air may exit, and cool air may enter the cabinet. In some instances, a small cooling fan may be required to insure adequate airflow through the cabinet. If you are in doubt about ventilation requirements for your specific installation, Please contact us. Avoid installation in humid locations, extremely hot or cold locations, or in areas that are exposed to direct sunlight, moisture or space heating equipment. GETTING STARTED Before proceeding, please observe the following precautions when connecting devices to your new Cinema 11a. Do not plug the power cord into your Cinema 11a until all other connections have been made. Always refer to the instructions that came with the component that you are connecting for specific procedures, warnings and options. For all analog connections, the red input jacks (R) are used for the right channel, and the white input jacks (L) are used for the left channel. (RCA connectors) Make sure to insert all plugs and connectors securely. Improper connections can result in noise, poor performance, or damage to the equipment. Do not bundle audio or video connection cables with power cords and speaker cables. Doing so may adversely affect the picture and sound quality. For example, run all the power cords down one side of the cabinet, all the signal cords down the other side, and the speaker wires down the center. When connecting devices to the digital inputs and outputs, you may also consider hooking up the analog connections to and from the components to insure that all signals can be employed by the preamp/processor. When using the TOSLINK optical input or output jacks, remove the protective cap and keep it in a safe place. When these jacks are not in use the protective cap should be replaced. When using a TOSLINK optical input or output jack, always use a high-quality optical fiber cable. IMPORTANT: We strongly recommend that before you connect any loudspeakers to your amplifiers, you complete all needed connections and set up procedures to your Cinema 11a as outlined below. This will reduce the chance that a wrong connection or other error will produce a high volume audio output that might damage your speakers or other components. Given the wide variety of components that can be connected to your Cinema 11a, there are numerous ways in which your system can be assembled. To help you with this task, use the chart at the end of this manual to record the co...