Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
40-17,000Hz (– 3dB) Monitor Output ............................................ 50-17,000Hz (– 3dB) Noise Level Mic (– 50)...................................................... – 55dB Line (+0) ....................................................... – 57dB T.H.D. ............................................................ 0.15% @ 1KHz MIC Input Level Electronic Balanced .................................... – 50dBu MIC Output Level Switchable Electronic Balanced ................ +0 / – 50dBu Unbalanced Output 3.5mm Stereo .............................................. – 50dBu Monitor Output 3.5mm Stereo (Max Load 16 ohm) ............. – 18dBu Main Output +6.5dBu with 600 ohm load ....................... 0dBu ref @ 0.775Vrms +13.5dBu with 1000 ohm load .................... 0dBu ref @ 0.775Vrms Unbalanced Output -32dBu with 600-1000 ohm load ................. 0dBu ref @ 0.775Vrms Battery Type/Duration 9-volt Alkaline (006p type) .......................... approx. 6 hours Current Draw 38mA nominal ............................................. 50mA maximum Size ............................................................... 42H x 130W x 103D mm 1.65 x 5.1 x 4.05 inches Weight with Battery .................................... 21.2 ounces 601 grams AB C DE Thank you for purchasing the Azden FMX-20 portable mixer. The FMX-20 has many unique features, so please read this manual completely before using the mixer. Designed to work with all microphones that have a low-impedance XLR output, the FMX-20 can be connected to any video camera or audio recorder, which has XLR, or mini-jack mic/line inputs. LOADING THE BATTERY: Make sure the mixer is turned off. Remove the battery cover (A) by turning the screw (B) counter- clockwise until it comes off. Place the battery strap (located in the battery compartment) around a new 9-Volt ALKALINE battery and insert it into the battery compartment. Be sure to follow the polarity diagram inside the battery compartment. If the polarity is correct the battery should go in easily. Do not force the battery into the compartment. If the battery does not go in easily turn it around and try again. Replace the battery door (A) and turn the screw (B) clockwise until tight, do not over tighten. A new 9-Volt ALKALINE battery should last for more than 6 hours. MOUNTING OPTIONS: 1) Belt Clip (supplied): The belt clip (C) can be attached to the backside of the mixer in 3 different positions. To remove the belt clip use a Philips head screwdriver and turn the screws (E) counterclockwise until they come off. To install the belt clip, select the desired location and turn the screws clockwise until tight. 2) Hook & Loop (supplied): Hook & Loop can be attached to either side of the mixer and to any adjoining flat surface (camera body, tripod, etc.) The Hook & Loop strip with the soft surface should be attached to the mixer and the Hook & Loop strip with the rough surface should be attached to the adjoining surface. 3) Strap (not supplied): A strap can be looped through the strap cutouts (D) on the sides of the mixer. CONTROLS and INPUTS/OUTPUTS 1 through 16 POWER SWITCH (1) and POWER LED (2): To power the FMX-20 by the internal battery. Move the POWERswitch (1) to INT position. The POWER ON LED (2) will turn green. When the battery voltage level is low the POWER ON LED (2) will turn to RED. When the POWER ON LED (2) turns to red replace the battery with a new 9-Volt ALKALINE battery. (see LOADING THE BATTERY above). When not in use turn the mixer OFF to conserve battery life. To power the FMX-20 with an external power supply. (Note: The FMX-20 does not come with an external power supply. An optional power supply part number BC-26U is available from the Azden parts department. Call 516-328-7500 for details. If you use a different power supply make sure its output does not exceed 12 volts or you may damage the unit.) Move the power switch (1) to EXT position. The POWER ON LED (2) will turn green. When not in use turn the mixer OFF and disconnect the power supply from the mixer. INPUT LEVEL CONTROLS for Channel 1 (3) and Channel 2 (4): CH1 (3): Controls the input level (volume) of the microphone connected to Input CH 1 (12). Zero is the lowest (quietest) setting, 10 is the highest (loudest). For the best possible sound and lowest noise increase the input level control until the input LED lights occasionally. CH2 (4): Controls the input level (volume) of the microphone connected to Input CH 2 (13). Zero is the lowest (quietest) setting, 10 is the highest (loudes...
Otros modelos de este manual:Instrumentos Musicales - FMX-20 (106.72 kb)