Votos - 5, Puntuación media: 4.4
(
)
)
|
Resumen del manual
Included Items • HardWire TL-2 Metal Distortion • HardWire StompLock™ • Foot Switch Glow Sticker • Hook-and-loop Pedalboard Pad • Warranty card 9 8 11 1 4 7 10 10 13 12 2 3 5 6 What Does This Do? 1. Level Knob - Controls the distortion output level. Turn the knob clockwise to increase and counter-clockwise to decrease the output level. 2. DC Adapter Jack - Connect (an optional) Harman PS200R power supply to this jack. Use the proper supply for your area’s mains line voltage. 3. High Knob (center) - Controls the level of high frequency (treble) boost/cut in the distortion effect.Turn the knob clockwise to increase and counter-clockwise to decrease treble level. 4. Low Knob (ring) - Controls the level of low frequency (bass) boost/cut in the distortion effect. Turn the knob clockwise to increase and counter-clockwise to decrease the bass level. 5. Mid Knob (center) - Controls the level of midrange boost/cut in the distortion effect. Turn the knob clockwise to increase and counter- clockwise to decrease the mid frequencies. 6. Freq knob (ring) - Controls the Midrange frequency that the Mid knob boosts and cuts. Range is 200 Hz to 5.0 kHz. 7. Gain Knob - Controls the overall distortion gain. Turn the knob clockwise to increase and counter-clockwise to decrease the amount of distortion gain. 8. Voicing Switch -This switches between the Metal Distortion’s two voicings. Tight provides a punchy articulated low-end response. Loose creates a thick heavy low end for grinding rhythm playing. 9. Input - Connect your instrument or the output of another pedal to this jack.This jack enables battery power to the pedal when connected. To prolong battery life, disconnect the cable from the Input jack when not in use. If the optional Harman PS200R power supply is used, cables can remain connected. 10. Foot Switch Release Pins -These two pins are spring loaded hinges that hold the Foot Switch in place. See page 7 for information on accessing and changing the battery. 11. Indicator LED - Lights when the effect is turned on.When battery power is low (approximately 15 minutes before it dies), the Indicator LED begins to dim giving you advanced warning that very shortly you will need to replace the battery. 12. Foot Switch -Turns the effect on and off. 13. Output - Connect this output to the input of your amplifier or the input of another pedal. Note: Use unbalanced mono instrument cables only. Amplifier Setup PS200R (optional) or Battery Operation In the event that battery power is completely depleted, HardWire pedals automatically switch into bypass.This eliminates the need to remove the pedal from your pedal chain if the battery is dead. To replace the battery, do the following: 1. Using the tip of a 1/4” guitar cable, push in one of the Release Pins in on either side of the Foot Switch, and remove it from the pedal chassis. 2. Remove the battery from the battery compartment and disconnect the battery cable. 3. Connect a new battery to the battery cable and put it back in the battery compartment. Make sure the battery cable does not interfere with the spring or pedal switch arm. 4. Place one hole of the Foot Switch over its corresponding pin. 5. Push the opposite pin in and lower the other side of the Foot Switch into place over the depressed pin. Release the pin.When the Foot Switch is properly fastened, both Release Pins are flush with the outer side of the pedal. Foot Switch Pedal Switch Arm Foot Switch Release Pin 9VDC Battery Foot Switch Release Pin Pedal Chassis Battery Compartment Spring HardWire Performance Accessories The performance accessories make integrating a HardWire pedal into any pedal board a snap.The following accessories are included: • Hook-and-loop Pedalboard Pad (designed to attach to the surfaces found on most commercial pedalboards) • Foot Switch Glow Sticker (easily visible on dark stages) • StompLock™ (keeps your settings where you want them) Hook-and-loop Pedalboard Pad To attach the Pedalboard Pad, do the following: 1. Peel off the existing rubber skid pad from the bottom of the pedal. 2. Peel the adhesive protector from the back of the Pedalboard Pad. 3. Apply the Pedalboard Pad to the bottom of the pedal. Foot Switch Glow Sticker To attach the Foot Switch Glow Sticker, do the following: 1. Peel the adhesive backing from the Foot Switch Glow Sticker. 2. Apply the Glow Sticker to the top of the Foot Switch. StompLock To place the StompLock over the pedal knobs, do the following: 1. Set the knobs to your preferred setting. 2. Gently push the StompLock over the top of the knobs. 3. To remove the StompLock, gently lift one side and then the other. Specifications Controls - Level, Low, Mid, Freq, High, Gain,Voice Switch, On/Off Pedal Jacks - Input, Output Input Impedance - >500 k. - effect on Output Impedance - 1 k. - effect on Input Impedance - true hardwire bypass - effect off Output Impedance - true hardwire bypass - effect off Power Supply - 9V Alkaline Dry Battery or Harman PS200R 9V DC power supply...