Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. ENGLISH kustom.com FRENCH kustom.com KXB1 Control Panel KXB11 2 3 4 6 7 85 1. Input Jack: .-inch input that is intended for bass guitar but will accept other instruments as well. 2. Volume: Adjust this control to set the desired volume level of the amplifier. Note: If you are using an instrument with a built-in active preamp, set its level to mid-position before increasing its volume or distortion may occur. 3. Bass: This control adjusts the lower frequencies to provide rich, full tones. It will boost or cut by 15 dB at 60 Hz. 4. Mid: This control adds a thick, punchy quality to your tone. It will boost or cut by 15 dB at 500Hz. 5. Treble: Increasing this control will add presence and attack to your bass tone. It will boost or cut by 15 dB at 10 kHz. 6. Aux In: This is a 3-conductor, 1/8-inch, stereo jack that allows playback from a Compact Disc, MP3 player or other audio device. The overall volume level will be determined by the audio device, so start with lower volume levels and increase as needed. 7. Headphones: This is a 3-conductor, 1/8-inch input jack intended for headphone use. The amplifier’s internal speaker is disconnected when this jack is used. 8. Power Switch: This dual-function component is both an On/Off power switch and a status indicator light. When illuminated, it shows that your amplifier is ready to be played. To turn amplifier on, press switch upward. To turn amp off, press switch downward. kustom.com KXB1 AC Mains kustom.com KXB1 Suggested Settings The following suggested settings will help you dial in a variety of popular tones. Keep in mind, these are starting points to get you up and running with your KXB amplifier. Feel free to experiment to achieve your own signature sounds. KXB1 TRADITIONAL/VERSATILE TONE In this setting, the amplifier will deliver a traditional, yet versatile, electric bass sound. Whether you are playing Rock, Country, Blues or Gospel, this setting will get you close. If you play with a pick and want less treble attack on the notes, decrease the amount of high frequencies using the Treble control. If you need a deeper bottom end, increase the amount of low frequencies using the Bass control. Adjust the amount of Midrange to best match the tone of your bass guitar and how it fits into the overall sound. KXB1 FUNKY, SLAPPED TONES This style of music needs a strong attack with lots of treble content. Using less Midrange will produce the extra top end necessary for this type of music. If you use a “slapping” thumb technique, add a bit more low end and extra volume – or less if you really hit the strings hard. Even though this is a practice or rehearsal-level amplifier, it will deliver the punch and clarity that you require. KXB1 ALTERNATIVE STYLE These settings are designed for upper-end punch and edge that will cut through most any sound mix. This tone will work well with pick or fingers. Make sure your bass guitar’s volume control is up all the way. Since you’re adding volume, be careful with the amount of Bass, Mid and Treble that you dial in, as it can also add some distortion to the sound. kustom.com Kustom® KXB1 Specifications Output Power 10 Watts 4 Ohms at 10% THD+N Speaker 1 X 6” Custom Designed 4 Ohms Input Impedance Single Input 470K Ohm Gain 48 dB Volume @ Max, All EQ at 12 o’clock S/N Ratio -80 dB typical Below rated power Aux Input 800 mV Sensitivity Stereo 3.5mm High Impedance Headphone Output 10 mW @ 30 ohms per channel Stereo 3.5mm Amplifier Tone Controls 60 Hz +/- 15 dB 500 Hz +/- 15 dB 10 Hz +/- 15 dB Power Requirements USA/Canada 120VAC/60Hz, 25W Europe 230VAC/50Hz, 25W UK 240VAC/50Hz, 25W Australia 240VAC/50Hz, 25W Japan 100VAC/50-60Hz, 25W Dimensions/Weight cm3/Kilogram 30.5 (Height) X 27.3 (Width) X 15.2 (Depth), 4.5 Kilogram Inches/Pounds 12 (Height) X 10.75 (Width) X 6 (Depth), 9.9 Lbs kustom.com KXB1 Signal Flow Diagram kustom.com kustom.com 19 November 2009 KXB1 Kustom Amplification, Inc. 3015 Kustom Drive Hebron, Kentucky USA 41048 888-4-KUSTOM (888-458-7866) All specifications are subject to change with...