Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Some setup required. Please read the following instructions before installing or using your new unit. HALOGEN LAMP WARNING! This fixture is fitted with a halogen lamp which is highly susceptible to damage if improperly handled. Never touch lamp with bare fingers as the oil from your hands will shorten lamp life. Also, never move fixture until lamp has had ample time to cool. Remember, lamps are not covered under warranty conditions. THE MIGHTY SCAN™ Features • 20 Dichroic Colors + White • 20 Gobos plus Spot • High speed Shutter • Strobes in every Color • 16 flashes per second • Variable Speeds • DMX-512 Protocol • Separate color and gobo wheels • Split colors • Full DMX capabilities • Build in programs * At first start-up, this unit may smoke for a few minutes until the excess paint can be burned off lamp socket assembly. Important Notice: This fixture follow the European DMX standard. When operating this fixture with a standard DMX controller, the fixture’s DMX value will start on one (1) with all the dip switches in the off position. For example: To get a DMX value of one (1) you would have to flip dip switch one (1) to the on position. In the case of the Mighty Scan™ however, dip switch one (1) on, would give the Mighty Scan™ a DMX value of two (2). To get a value of one (1), all the dip switches would have to be in the off position. To get a DMX value of two (2) set the DMX value to one (1), for thee (3) set the DMX value for two (2) and so on. THE MIGHTY SCAN™ Specifications Voltage: 120v/220v 50/60 Hz Dimensions: 14.25” x 5.75” x 7.5” Lamp: ZB-ELC-3 250W 24V Weight: 28 lbs. Fuse: Dual 6.3A Packing list: 1. The MIGHTY SCAN™ Projector 2. IEC power cord 3. Operating manual American DJ Supply® MIGHTY SCAN™ User Instructions page 1 Precautions: 1. Never operate unit when case is open. 2. Never cover unit as this may block air vents and cause overheating and possible fire hazard. 3. Never operate unit in the rain or in damp moist conditions as this could cause electric shock. 4. Follow standard electrical safety precautions when installing, operating or servicing the unit to prevent electrical shock, fire, or equipment damage. 5. Make sure head and yoke rotate freely 6. These units are for commercial use and contain no user-serviceable parts inside. 7. Refer servicing to an authorized American DJ service center. Make sure to clean the fan openings, air channels and fan gratings regularly. Getting Started Inspection Every Mighty Scan™ has been thoroughly tested and lamped before leaving the factory. Carefully unpack the fixture and inspect the unit for damage that may have occurred during shipping. Projector Installation 1. After removing the Mighty Scan™ from the shipping container, remove the hanging brackets knobs that have been inserted in the styrofoam packing material. The knobs are used to hold the fixtures’ angle. Without the knobs the weight of fixture will not allow the unit to hold your desired operating angle. 2. This unit can be hung or placed in any safe, secure position. 3. To securely mount the fixture to truss, be sure to use a minimum 35Kg rated clamp and always try to use a safety cable when ever possible. 4. Try not to mount the fixture too close to walls or other fixtures, this will allow for proper cooling. 5. Connect the IEC power cord into the top of the unit (See diagram 10). 6. Set the dip switches according to your desired operation mode [See Operation Mode on pages three (3), four (4), and five (5)]. 7. Plug the power cord into a properly grounded electrical socket. Do not attempt to brake off or by-pass the ground prong on the power cord, this is used for safety to reduce the risk of fire in case of an electrical short. 8. After plugging the unit in, the lamp will ignite and the unit will reset to the home position making a clicking noises and returning the mirror to center home position. Lens Focusing 1. Hang the fixture in your final desired position. 2. If no controller is being used, A. Set dip switch ten (10) to the on position (See diagram 2). B. Turn the sensitivity to minimum position (See diagram 4). C. Plug the fixture in. The unit’s shutter will open and the mirror will reset to the center. 3. If a controller is being used, A. Plug the fixture in. B. Use your controller to set the fixture’s mirror in a center home position. C. Open the shutter and select a gobo. 4. Adjust lens by turning it in a clockwise and counter-clockwise direction until the projected pattern is in a sharp focus. *Check that the voltage marked on the back of the unit is correct for your area. American DJ Supply® MIGHTY SCAN™ User Instructions page 2 Operation Modes Important Notice: When setting or changing your dip switches it is best to disconnect power so the unit can reset to the new settings. Stand Alone Operation: This operation is used to control one or more fixtures to the built in programs. Use this operation mode if; 1) You will not be using a DMX co...