Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Any other use is not as specified. Use not as specified, modification of the tool or use of parts not approved by the manufacturer can cause unforeseeable damage! 3.2 General Safety Instructions • When using this air tool observe the following safety instructions to minimize the risk of personal injury or material damage. • Please also observe the special safety instructions in the respective chapters. • Observe the statuary accident insurance institution regulations and regulations for the prevention of accidents pertaining to the operation of air compressors and air tools, where applicable. A General danger! • Keep your work area tidy – a messy work area invites accidents. • Be alert. Do not operate this tool while under the influence of drugs, alcohol or medication. • Keep the tool from jamming – ensure firm footing when using the tool. • Always use a quick coupler to connect this air tool to a compressor. • Make sure that the max. permissible working pressure stated in the Technical Specifications is not exceeded. • Do not overload tool – use it only within the performance range it was designed for (see Technical Specifications). • Do not touch any rotating parts. • Disconnect tool from air supply before changing sockets or if left unattended. A Hazard generated by insufficient personal protection gear! • Wear hearing protection. • Wear safety glasses. A Hazard generated by tool defects! • Do not attempt to repair the tool yourself! Only trained specialists are permitted to service or repair compressors, pressure vessels and air tools. A Caution! Protect the tool, air inlet, square drive and operating elements in particular, from dust and dirt. 3.3 Symbols Used Danger! Neglect of the following warnings may cause serious injury or material damage. Read instructions. Wear hearing protection. Wear safety goggles. 4. Operation 4.1 Before Initial Operation • Install the plug nipple. 4.2 Using the Tool A Caution! To ensure a long service life of this tool, it needs to be supplied with sufficient quantities of pneumatic oil. This can be achieved by: . a service unit with oiler at the compressor. . a lubricator, installed directly on the air tool or in the air line. ENGLISH . adding approx. 3-5 drops of pneumatic oil by hand every 15 minutes of operation (continuous operation) to the air inlet. 1. Put socket on the drive. 2. Set direction of rotation with the reversing knob: . reversing knob set to the left: forward/driving . Reversing knob set to the right: R = reverse/loosening 3. Adjust working pressure at the compressor (see Technical Specifications for max. permissible working pressure). 4. Connect quick coupler to the air supply. 5. Pull trigger to start. 5. Care and Maintenance A Danger! Always disconnect from air supply before servicing. Repair and maintenance work other than described in this section must 9. Technical Specifications be carried out by qualified specialists only . • Check all screwed connections for tightness, tighten if necessary. • When the tool is not lubricated by a service unit or line oiler, manually add 3 - 5 drops of pneumatic oil for every 15 minutes of operation (continuous operation) into the air inlet. • Never store the tool outdoors, in unprotected areas or in damp locations. 6. Available Accessories • Pneumatic oil 0.5 litre Special lubricant for air tools, service units and line oilers. Stock-no. 090 100 8540 • Line oiler R1/4" female For fitting directly to air tools. Oil level can always be checked through sight glass. Stock-no. 090 105 4584 • Swivel-type air inlet DKG 1/4" For fitting directly to air tools. Improves tool manoeuverability. Stock-no. 090 106 0991 • Socket set 1/2" consisting of 10 sockets (10, 11, 12, 13, 15, 17, 19, 21, 22, 24 mm). 7. Repairs A Danger! Repairs to air tools must be carried out by qualified specialists ONLY! Air tools in need of repair can be send to the service centre in your country. See Spare Parts List for address. Please attach a description of the fault to the air tool. 8. Environmental Protection The tool's packaging materials are 100 % recyclable. Worn out machines and accessories contain considerable amounts of valuable raw and plastic materials, which can be recycled. These instructions are printed on paper produced with elemental chlorine free bleaching process. Model RS 4000 Air consumption l/min 490 Max. permissible working pressure bar 6.2 Speed min-1 160 Square drive " 1/2 Maximum bolt size M13 Maximum torque (forward) Nm 95 Maximum torque (reverse) Nm 95 Minimum hose size (inner) mm 13 Vibration (effective value of weighted acceleration) m/s2 1.13 Sound power level LWA Sound pressure level LPA dB (A) dB (A) 92.9 103.9 Dimensions: length x width x height mm 305 x 46 x 48 Weight kg 1.2 FRANCAIS 1. Vue d'ensemble de l'appareil 1 2 3 6 54 1 Bouton d'inversion droite/gauche 2 Poignee 3 Logement pour embout (raccord air comprime) 4 Gachette 5 Sortie d'air insonorisee 6 Embout carre (1/2 ") pour douilles Sans illustration : Embout...