Votos - , Puntuación media:
(
)
)
Fabricar: Philips
Tamaño del archivo: 726.58 kb
Nombre del archivo:
Idioma del manual:
El documento se está cargando, por favor, espere
 |
El documento se está cargando, por favor, espere
Resumen del manual
The louder the volume, the shorter the safe listening time is. Be sure to observe the following guidelines when using your headset. • Listen at reasonable volumes for reasonable periods of time. • Be careful not to adjust the volume continuously upwards as your hearing adapts. • Do not turn up the volume so high that you can’t hear what’s around you. • You should use caution or temporarily discontinue use in potentially hazardous situations. • Excessive sound pressure from earphones and headset can cause hearing loss. • Using the headset with both ears covered while driving is not recommended and may be illegal in some areas while driving. • For your safety, avoid distractions from music or phone calls while in traffic or other potentially dangerous environments. General information To avoid damage or malfunction: Caution ••Do not expose the headset to excessive heat. ••Do not drop your headset. ••Headset shall not be exposed to dripping or splashing. ••Do not allow your headset to be submerged in water. ••Do not use any cleaning agents containing alcohol, ammonia, benzene, or abrasives. ••If cleaning is required use a soft cloth, if necessary dampened with a minimum amount of water or diluted mild soap, to clean the product. ••The integrated battery shall not be exposed to excessive heat such as sunshine, fire or the like. About operating and storage temperatures and humidity • Operate or store in a place where temperature is between -15.C (5.F) and 55.C (131.F) (up to 90% relative humidity. • Battery life may be shorter in high or low temperature conditions. Compliance with EMF This product complies with all applicable standards and regulations regarding exposure to electromagnetic fields. 2 EN 2 Your Bluetooth stereo headset Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at With this Philips wireless on-ear headset, you can: • enjoy convenient wireless handsfree calls; • enjoy and control wireless music; • switch between calls and music; • enjoy music on non-Bluetooth devices with an audio cable. What's in the box Philips Bluetooth stereo headset SHB7150 USB charging cable Audio cable Quick start guide Other devices A mobile phone or device (e.g. notebook, PDA, Bluetooth adapters, MP3 players etc) which supports Bluetooth and is compatible to the headset. EN Overview of your Bluetooth stereo headset a Microphone b Call/Music button c Audio input jack d Volume/Track control e Charging slot EN 3 Get started Charge your headset Note ••Before you use your headset for the first time, charge the battery for 4 hours for optimum battery capacity and lifetime. ••Use only the original USB charging cable to avoid any damage. ••Finish your call before charging the headset, as connecting the headset for charging will power the headset off. Connect the supplied USB charging cable to: • the USB connector of the headset and; • USB power source. »»LED turns white during charging and turns off when the headset is fully charged. Tip ••Normally, a full charge takes 3 hours. ••When your battery is empty, you can carry on listening music with an audio cable. Make sure the headset is off (and not in idle mode) before using this audio cable. Pair the headset with your mobile phone Before you use the headset with your mobile phone for the first time, pair it with a mobile phone. A successful pairing establishes a unique encrypted link between the headset and mobile phone. The headset stores the last 8 devices in the memory. If you try to pair more than 8 devices, the earliest paired device is replaced by the new one. There are two ways to pair your headset with your mobile phone: • Manual pairing • NFC pairing Manual pairing 1 Make sure that the mobile phone is turned on and its Bluetooth feature is activated. 2 Make sure that the headset is fully charged and turned off. 3 Press and hold until the blue and white LED flashes alternately. »»The headset remains in pairing mode for 2 minutes. 4 Pair the headset with the mobile phone. For detailed information, refer to the user manual of your mobile phone. NFC pairing 1 Make sure that the mobile phone is turned on. 2 Make sure that the headset is fully charged and turned off. 3 Press and hold until the blue and white LED flashes alternately.. 4 Make sure you turn on the NFC function on your phone and your phone’s screen remains active. 5 Place your phone over the headset so that the NFC detection area of each device can touch each other. Note ••Make sure your mobile phone has the NFC feature available and switched on. ••Make sure your mobile phone is not in standby mode. ••Pairing with NFC is only suitable for Android mobile operating system 4.2 or above. ••Refer to the user manual of your mobile phone to identify its NFC detection area. EN The following example shows you how to pair the headset with your mobile phone. 1 Activate the Bluetooth feature of your mobile phone,...