Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
Choosing an ISP You must set up Internet service before you can connect to the Internet. The computer includes the New Connection Wizard to help you set up a new Internet account or configure the computer to use an existing account. Using the New Connection Wizard The New Connection Wizard works under the following conditions: You already have an account with an ISP. You have a disc from an ISP. You do not have an Internet account and would like to select an ISP from the list provided within the wizard. You have selected an unlisted ISP and the ISP has provided you with such information as a specific IP address and POP3 and SMTP settings. To access the New Connection Wizard, select Start > Help and Support. If you are prompted within the wizard to choose between enabling or disabling the Windows Firewall, choose to enable the firewall. Choosing the type of Internet connection You can choose one or more of the following methods to connect to the Internet: Broadband service—High-speed Internet access is provided by an ISP through one of the following services: Cable modemDigital Subscriber Line (DSL) SatelliteOther servicesBroadband service may require additional hardware and/or software provided by the ISP. WLAN—Internet connection through a WLAN requires broadband wired service with an ISP as well as a wireless router (purchased separately). Tolearn about setting up wireless access, see the HP Web site at (English only). Dial-up—You can access the Internet by dialing in to a service provider using a modem cable connected to the RJ-11 (modem) jack. To see wireless regulatory notices, refer to the section of the Regulatory, Safety and Environmental Notices that applies to your country or region. These notices are located in Help and Support. BBackup and recovery Creating recovery discs After setting up the computer for the first time, be sure to create a set of recovery discs of the full factory image. The recovery discs are used to start up (boot) the computer and recover the operating system and software to factory settings in case of system instability or failure. Note the following guidelines before creating recovery discs: You will need high-quality CD-R, DVD-R, or DVD+R media (purchased separately). .Formatted DVD±RW discs and DVD±RW double-layer discs are not compatible with HP Backup & Recovery Manager. The computer must be connected to AC power during the process. Only one set of recovery discs can be created per computer. Number each disc before inserting it into the optical drive of the computer. If necessary, you can cancel the disc creation before you have finished creating the recovery discs. The next time you select Create a set of recovery discs (Recommended), you will be prompted to continue the disc creation. To create a set of recovery discs: 1.Select Start > All Programs > HP Backup & Recovery > Backup & Recovery Manager. 2.Click Next. 3.Click Create a set of recovery discs (Recommended), and then clickNext. 4.Follow the on-screen instructions. Backing up your information You can only recover files that you have previously backed up. HP recommends that you use HP Backup & Recovery Manager to create an entire drive backup as soon as you set up your computer. With HP Backup & Recovery Manager, you can perform the following tasks: Backing up your information regularly to protect your important system filesCreating system recovery points that allow you to reverse undesirable changes to your computer by restoring the computer to an earlier stateScheduling backups at specific intervals or events When to back up On a regularly scheduled basis .Set reminders to back up your information periodically. Before the computer is repaired or restoredBefore you add or modify hardware or software Backup suggestions Create a set of recovery discs using HP Backup & Recovery Manager. Create system recovery points using HP Backup & Recovery Manager, and periodically copy them to disc. Store personal files in the Documents folder and back up these folders periodically. Back up templates stored in their associated programs. Save customized settings in a window, toolbar, or menu bar by taking a screen shot of your settings. The screen shot can be a time saver if you have to reset your preferences. To copy the screen and paste it into a word-processing document: a.Display the screen. b.Copy the screen. To copy only the active window, press alt+fn+prt sc. To copy the entire screen, press fn+prt sc. c.Open a word-processing document, and then select Edit > Paste. Before you can perform backup and recovery procedures, the computer must be connected to external power. Drivers, utilities, and applications installed by HP can be copied to a CD or to a DVD using HP Backup & Recovery Manager. Backing up specific files or folders You can back up specific files or folders to the recovery partition on the hard drive, to an optional external hard drive, or to optical discs (CDs or DVDs)...
Otros modelos de este manual:Notebooks - HP 530 Notebook PC (2.53 mb)